Thermal Expansion · Explained · Beginner
Thermal Machine Configuration & Blue/Orange I/O Logic Explained
Mastering the internal side configuration of Thermal Expansion machines is the key to building clean, pipe-free automated processing lines. In this guide, you will learn how to use the iconic Blue and Orange input/output logic, enable automatic item movement, and control your machines with Redstone.
What you need
- Any Thermal Expansion Machine (such as a Redstone Furnace, Pulverizer, or Induction Smelter)
- A Redstone Flux (RF) or Forge Energy (FE) power source (such as a Stirling Dynamo)
- Two Chests or Barrels for testing item input and output
- A Crescent Hammer (optional, for quick external adjustments)
- A Lever (optional, for testing Redstone Control modes)
Step by step
1Place Your Machine and Inventories
Place your Thermal Expansion machine, such as a Pulverizer, on the ground and connect it to a Dynamo or energy cable from the back or bottom. Place one Chest directly on top of the machine to hold raw materials, and a second Chest directly to the right of the machine to collect finished products. Right-click the machine to open its graphical user interface (GUI).
Tip: You can place chests on any face of the machine; top and right are just the easiest for visualizing your first setup.
2Locate the Configuration Tab
Look at the right edge of the machine's GUI to find a series of colored tabs. Click the gear icon tab, labeled Configuration, to expand the side selection menu. You will see a flattened cross-shaped diagram representing all six physical faces of the machine block, along with two toggle buttons on the left side of the tab.
Tip: The center square of the cross always represents the front face of the machine that is looking at you.
3Understand the Color-Coded Slots
Look closely at the main inventory area of the machine GUI while the Configuration tab is open. You will notice colored borders around the item slots and fluid tanks: a Blue border highlights input slots, while an Orange border highlights output slots. Some complex machines like the Pulverizer or Induction Smelter may also display specific shades for primary versus secondary outputs, or a Purple border allowing both input and output simultaneously.
4Configure the Input Face (Blue)
In the Configuration tab diagram, find the top square, which corresponds to the top face of your machine where you placed the first chest. Left-click this top square once until its border turns Blue. This tells the machine that the top physical face is now directly linked to the Blue input slots inside the machine.
Tip: Right-clicking a face cycles through the colors in reverse order, while Shift-left-clicking resets that face to None.
5Configure the Output Face (Orange)
Next, look at the right square in the cross diagram, which represents the right side of the machine from your perspective when facing the front. Click this square until it turns Orange (or the specific output color matching both primary and secondary output slots). This links the right physical face of your machine to its internal output slots.
Tip: Be mindful that 'left' and 'right' on the diagram are relative to you looking directly at the front of the machine.
6Enable Auto-Input and Auto-Output
Even with the sides colored, items will not move into or out of ordinary chests on their own yet. Look at the two buttons to the left of the cross diagram in the Configuration tab: click the arrow-pointing-in icon to enable Auto-Input, and click the arrow-pointing-out icon to enable Auto-Output. Once both buttons look illuminated, drop some raw ore into your top chest and watch the machine automatically pull it in, process it, and push the results into the right chest.
Tip: Auto-Input and Auto-Output work without consuming extra power in modern Thermal Series versions.
7Set Up Redstone Control
On the left or right side of the GUI, click the Redstone Torch tab to open the Redstone Control panel. Here you have three modes: Ignored (the machine always runs regardless of signals), Low (the machine runs by default and stops when powered by Redstone), and High (the machine stays off and only runs when given an active Redstone signal). Select High, place a Lever on the machine, and flip it to gain manual switch control over your processing line.
Tip: In older 1.12.2 versions of Thermal Expansion, you may need to craft and install an Integrated Redstone Circuit augment if this tab does not appear by default.
How it works
At its core, Thermal Expansion treats each of the six faces of a machine block as a virtual valve connected to specific internal inventory slots. When a face has no color (blank), the valve is closed, and hoppers or pipes attached to that side cannot see the machine's inventory. When you paint a face Blue or Orange, you are mapping that physical side of the block to the matching color-coded slots inside the GUI.
Coloring a face only grants access; it does not actively move items by itself. If you attach an external pipe or vanilla Hopper to a Blue face, the Hopper provides the pushing force. However, enabling the machine's internal Auto-Input and Auto-Output toggles activates an internal transfer engine. Every few game ticks, the machine scans adjacent blocks on Blue faces to pull items in, and scans adjacent blocks on Orange faces to push finished items out. This allows you to chain machines directly next to each other—for example, setting a Pulverizer to auto-output Orange into the right side, and placing a Redstone Furnace directly to its right with its left side set to Blue.
The Redstone Control logic acts as a master switch for both the machine's processing cycle and its auto-transfer engine. When a machine is disabled via Redstone Control, it immediately pauses its current recipe and stops pulling or pushing items, allowing you to use vanilla Comparators and Redstone signals to prevent overflow in your storage systems.
Common mistakes
- Confusing Left and Right perspectives: The left and right squares in the Configuration tab are from the player's viewpoint looking at the front face of the machine, not from the machine's internal perspective.
- Forgetting to turn on Auto-Input/Auto-Output: Coloring the sides Blue and Orange only opens the slots to that side; if you are using plain chests without pipes, you must also click the Auto-Input and Auto-Output buttons or nothing will move.
- Blocking the front face by accident: While the front face usually cannot be reconfigured, placing blocks or chests directly in front of the machine makes it hard to click and check its active animation state.
- Mismatched secondary outputs: On machines like the Pulverizer or Sawmill that produce bonus byproducts, setting a side to primary output only will leave the secondary slot clogged. Always use the combined Orange output color if you want all results going to the same chest.
FAQ
Why isn't my machine pulling items from the chest even though the side is Blue?
Check two things: first, ensure the Auto-Input button (to the left of the cross diagram in the Configuration tab) is clicked and highlighted. Second, make sure the item in the chest is actually a valid recipe ingredient for that specific machine by checking JEI.
Can I input and output through the exact same face of a machine?
Yes! Cycle through the colors on a single face until it shows the split Blue/Orange icon (or Purple in some versions). This allows that face to both accept raw ingredients and eject finished products, which is very useful when using advanced item pipes or AE2/Refined Storage interfaces.
Do I need to open the GUI to change sides every time?
No. If you hold a Crescent Hammer (or any compatible mod wrench), you can sneak-right-click or use the tool's specific configuration mode on the outside face of a machine to cycle its I/O colors directly in the world.
Can two Thermal machines pass items directly to each other without chests or pipes?
Yes. Place two machines side-by-side. Set the touching face on the first machine to Orange with Auto-Output enabled, and set the touching face on the second machine to Blue. The first machine will push its results straight into the second machine's input slot.
By combining Blue input faces, Orange output faces, and the built-in Auto-I/O toggles, you can automate any Thermal Expansion machine line cleanly without needing external pipes or hoppers.