Powah! (Rearchitected) · Early game
Passive Thermo Generator & Blazing Crystal Array
The Passive Thermo Generator & Blazing Crystal Array is a zero-maintenance, early-game power plant designed to run indefinitely without consuming fuel items. By pairing Powah's Thermo Generators with the high heat multiplier of Blazing Crystal Blocks and a self-replenishing water supply, you achieve reliable base power. This setup is ideal for bootstrapping your energy grid and charging your initial Energy Cells with minimal effort.
- Footprint
- 5x3x3 blocks
- Power
- ~400 to 1,200 FE/t depending on tier (check JEI)
- Throughput
- Continuous passive generation
- Difficulty
- beginner
Flow diagram
How items, fluids and energy move through the setup, left to right.
Swipe sideways to see the whole diagram
Materials
| Item | Count |
|---|---|
| Thermo Generator (Basic or Hardened) | 4 |
| Block of Blazing Crystal | 4 |
| Energy Cable (Basic or Hardened) | 6 |
| Energy Cell (Basic or Hardened) | 1 |
| Energizing Orb | 1 |
| Energizing Rod (Basic) | 2 |
| Water Bucket | 2 |
| Modded Fluid Pipe or Pump (Any compatible mod) | 5 |
Build it step by step
1Energize the Blazing Crystals
Before building the array, set up a temporary Energizing Orb and two Basic Energizing Rods powered by a Starter Furnator. Craft 36 Blazing Crystals by energizing Blaze Rods or Blaze Powder (check JEI for your modpack's exact recipe and power cost). Compress these 36 crystals into 4 Blocks of Blazing Crystal in a crafting table.
2Lay the Heat Foundation
Dig a 4-block-long, 1-block-deep trench in the floor where you want your array to sit. Place the 4 Blocks of Blazing Crystal in a straight line inside this trench so their top faces are flush with the floor. These blocks will remain permanently hot and never degrade.
3Install the Thermo Generators
Place your 4 Thermo Generators directly on top of the 4 Blocks of Blazing Crystal. Right-click one of the generators to open its GUI and confirm that it recognizes the heat source underneath. You will notice it does not produce power yet because the internal coolant tank is empty.
4Connect the Water Coolant Loop
Dig a 3x1 trench behind the array and use your two Water Buckets to create an infinite water source. Run your fluid pipes or pump from the middle water source block along the back faces of all 4 Thermo Generators. Once water fills their internal tanks, the generators will immediately begin producing FE.
5Wire the Energy Output
Run your Powah Energy Cables along the top face of all 4 Thermo Generators. Connect the end of this cable line into one face of your Energy Cell to buffer the power. Finally, attach an output cable to a different face of the Energy Cell to feed your base's machines.
6Configure Cell I/O
Open the Energy Cell GUI and verify the side configuration. Ensure the side connected to the generators is set to 'In' (or 'In/Out') and the side leading to your machines is set to 'Out'. Your passive power plant is now fully operational.
How it works
The Thermo Generator is a passive power block in Powah! (Rearchitected) that generates Forge Energy when two conditions are met: it must be placed directly above a valid heat source, and it must be supplied with a liquid coolant (standard Water). While vanilla Lava or Magma Blocks can be used underneath for a baseline 100% heat rating, using a Block of Blazing Crystal drastically increases the heat multiplier (typically 280%, check JEI for exact pack configurations), nearly tripling the FE/t output of every generator without increasing the physical footprint.
Because the heat source underneath is never consumed, the only upkeep required by the system is a very slow trickle of water. By automating water insertion via the back face and extracting energy from the top face, the array achieves 100% uptime. Routing the generated power into an Energy Cell acts as a vital buffer, allowing your early-game base to handle sudden power spikes from ore processing or energizing recipes while the Thermo Generators steadily recharge the cell during downtime.
Upgrades and scaling
- Upgrade the Thermo Generators through the Powah tiers (Blazing, Niotic, Spirited, Nitro) inside the Energizing Orb to exponentially increase FE/t output on the exact same footprint.
- Replace the Blocks of Blazing Crystal underneath with Soul Lava (if available in your modpack) for an even higher heat multiplier.
- Tile the design horizontally or vertically; a single infinite water pump can easily supply dozens of Thermo Generators at once.
- Swap the Energy Cell for an Ender Cell to broadcast your passive power wirelessly across dimensions via your personal Ender Network.
Common mistakes
- Using individual Blazing Crystals instead of crafting them into a full Block of Blazing Crystal to place in the world.
- Forgetting to supply continuous water; Thermo Generators slowly consume water as coolant and will stall once their internal tank hits zero.
- Connecting Starter or Basic Energy Cables to a very large array of upgraded Thermo Generators, which bottlenecks the total FE/t transfer rate.
- Placing the heat source adjacent to the generator instead of directly beneath its bottom face.
FAQ
Does the Block of Blazing Crystal ever run out of heat or decay?
No. Once placed in the world, the Block of Blazing Crystal provides a permanent, infinite heat source that never degrades or turns into obsidian.
Does Powah! include its own water pump or fluid pipes?
No, Powah! focuses strictly on energy generation, storage, and transfer. For an automated setup, you will need a basic fluid pipe or pump from a companion tech mod in your modpack, though you can manually fill the generators with water buckets in a pinch.
Can I use coolants other than water inside the Thermo Generator?
No, unlike the Reactors which accept solid coolants like Dry Ice alongside water, the Thermo Generator strictly uses standard liquid Water as its fluid coolant (unless modified by a specific modpack script; check JEI).