Powah! (Rearchitected) · Mid game
Automated Energizing Orb Crafting Matrix
The Energizing Orb from Powah! (Rearchitected) is notoriously tricky to automate because stuffing multiple sets of ingredients inside it at once stalls the crafting process completely. This setup uses a simple vanilla Redstone Comparator latch combined with a dropper and hopper system to feed exact single-item or multi-item recipe batches only when the Orb is completely empty. Surrounding the core with multiple mid-tier Energizing Rods ensures rapid processing without manual babysitting.
- Footprint
- 5x5x4 blocks
- Power
- ~10-20 kFE/t depending on Rod tier (check JEI)
- Throughput
- 1 recipe batch every 2-5 seconds
- Difficulty
- intermediate
Flow diagram
How items, fluids and energy move through the setup, left to right.
Swipe sideways to see the whole diagram
Materials
| Item | Count |
|---|---|
| Energizing Orb | 1 |
| Energizing Rod (Blazing) | 4 |
| Energy Cable (Blazing) | 8 |
| Wrench (Powah!) | 1 |
| Redstone Comparator | 1 |
| Redstone Torch | 1 |
| Redstone Dust | 3 |
| Dropper | 1 |
| Hopper | 2 |
| Chest or Barrel | 2 |
| Building Blocks | 6 |
Build it step by step
1Place the Output and Core
Place your Output Barrel on the ground level. Attach an Output Hopper feeding into the back or top of this barrel, then place the Energizing Orb directly on top of that hopper. The Orb naturally restricts outputs so that hoppers underneath can only pull finished crafts, never raw inputs.
2Install the Batch Dispenser
Place a Dropper directly adjacent to the Energizing Orb, facing into it. Connect an Ingredient Feeder Hopper into the top of this Dropper, and place your Input Chest on top of the hopper. This staging setup holds items back until a redstone pulse requests them.
3Wire the Comparator Sensor
Place a solid building block behind the Energizing Orb and set a Redstone Comparator on it, reading outward from the Orb. The Energizing Orb has a special redstone property: it emits a comparator signal as long as there is at least one item inside it.
4Build the Inverter Latch
Place a solid block directly in front of the Redstone Comparator and attach a Redstone Torch to the side of that block facing toward your Dropper. Run a short line of Redstone Dust from the torch to the Dropper. When the Orb is empty, the comparator turns off, the torch turns on, and the Dropper fires one item into the Orb, which immediately turns the comparator back on and locks the system.
5Set Up Multi-Item Recipe Timing (Optional)
If you are crafting Energized Steel (which requires both Iron and Gold), place a segundo Dropper facing into the Orb on the opposite side, wired to the exact same Redstone Torch line. Load Iron into one Dropper's chest and Gold into the other; a single pulse from the torch will simultaneously inject one of each item into the Orb.
6Mount the Energizing Rods
Build four pillars or a ring of Energy Cable (Blazing) two blocks away from the Energizing Orb. Mount four Energizing Rod (Blazing) units directly onto the cables. They can be placed facing any direction as long as they are within range of the Orb.
7Link Rods to the Orb
Equip your Powah! Wrench and shift-right-click it to set it to 'Link Mode'. Right-click an Energizing Rod and then right-click the Energizing Orb to manually bind them if they have not auto-linked. Connect your main base power grid to the Energy Cables to begin crafting.
How it works
The core challenge of automating Powah!'s Energizing Orb is that it has no internal recipe filter; if a standard hopper dumps 64 Blaze Rods into it, the Orb sits idle because no recipe calls for 64 Blaze Rods. By reading the Orb with a Redstone Comparator, we utilize its built-in occupancy detection. The moment the Orb becomes empty, the comparator signal drops to zero.
Dropping the signal to zero allows our inverting Redstone Torch to turn on, sending a single rising-edge pulse to the Dropper(s). Each active Dropper instantly pushes exactly one item into the Energizing Orb. As soon as that item enters the Orb, the comparator immediately detects it and outputs a redstone signal again, turning off the Redstone Torch and preventing any further items from being inserted until the craft finishes.
Meanwhile, the Output Hopper beneath the Energizing Orb constantly tries to pull items out. Because the Energizing Orb is coded to lock input slots from bottom extraction, the hopper ignores the raw ingredients while the Energizing Rods fire their lasers. Once the energy threshold is met, the ingredients transform into the final product and move to the internal output slot, where the bottom hopper instantly extracts it, resetting the comparator loop for the next batch.
Upgrades and scaling
- Upgrade the Energizing Rods from Blazing to Niotic, Spirited, or Nitro tiers as you progress to dramatically decrease crafting times for high-FE recipes.
- Add more Energizing Rods around the perimeter; you can fit dozens of rods within the valid radius of a single Orb to multiply your total FE/t transfer rate.
- If playing in a modpack with Modular Routers, Applied Energistics 2, or Refined Storage, replace the Chest and Dropper assembly with an ME Pattern Provider set to 'Blocking Mode' to handle variable multi-item recipes dynamically from one block.
Common mistakes
- Feeding items directly into the Energizing Orb with a Hopper instead of a Dropper; hoppers push items too fast for the comparator loop to lock properly unless carefully throttled, leading to two items entering at once.
- Placing multiple Energizing Orbs too close together without manually linking the Rods using the Powah! Wrench in Link Mode, causing Rods to split their lasers between the wrong Orbs.
- Mixing different ingredients in a single Dropper for 2-item recipes like Energized Steel; because Droppers choose a random slot to eject from, you must use two separate Droppers (one per ingredient type) triggered by the same redstone line.
- Using low-tier Energy Cables with high-tier Energizing Rods, which creates a power bottleneck where the cables cannot supply enough FE/t to keep the rods firing continuously.
FAQ
How do I automate 2-item or 4-item recipes like Energized Steel or Nitro Crystals?
Use one separate Dropper facing the Orb for each required item slot in the recipe, all wired to the exact same Redstone Torch. For example, for Energized Steel, use two Droppers (one filled with Iron, one with Gold); when the Orb is empty, both fire simultaneously, inserting the exact 1:1 pair.
Why aren't my Energizing Rods shooting lasers at the Orb?
Ensure the Rods are mounted directly onto powered cables or batteries, are within a 9x9 area around the Orb, and are linked to it. Craft a Powah! Wrench, shift-right-click to switch to Link Mode, and click the Rod then the Orb.
Does the Energizing Orb itself need an Energy Cable attached to it?
No, the Energizing Orb cannot accept power directly from cables. It only receives energy wirelessly via the laser beams emitted by nearby Energizing Rods.