Oritech · Setup guide · Advanced
How to Build and Use the Particle Accelerator
Mastering the Particle Accelerator is the ultimate milestone in Oritech, unlocking exotic end-game materials, high-tier cybernetic augmentations, and advanced crafting components through high-energy physics. This guide covers how to design an efficient accelerator ring, meet its massive energy demands, and execute successful particle collisions without wasting power or destroying your payloads.
What you need
- Accelerator Controller (1x per ring, or 2x for dual-emitter collision setups)
- Accelerator Ring blocks (dozens to hundreds, depending on your ring perimeter)
- Accelerator Motor blocks (for boosting particle velocity along straightaways)
- Accelerator Sensor blocks (optional, for monitoring speed and automation)
- Particle Collector (required for harvesting collision energy and byproducts)
- High-tier Machine Cores (needed to craft the multiblock components in the Assembler)
- Energy Pipes and High-Capacity Energy Storage
- Wrench (for orienting ring pieces and configuring pipe connections)
- EMI, JEI, or the Oracle Index in-game guide (essential for checking exact collision velocity thresholds)
Step by step
1Prepare a Large, Flat Construction Area
Before crafting the blocks, clear out a massive, completely flat horizontal plane in your base or a dedicated dimension. Because particles lose speed when turning corners, your ring needs long straightaways to reach end-game collision velocities. A minimum clearing of 30x30 blocks is recommended for an entry-level accelerator, though late-game recipes benefit from much larger tracks.
Tip: Build the accelerator in a chunk-loaded area or keep the entire ring within active simulation distance so particles do not freeze mid-flight.
2Fabricate the Accelerator Components
Using your Assembler and Foundry, produce your Accelerator Controller, Accelerator Motors, and a large batch of Accelerator Ring blocks. You will need advanced alloys, plastic, and high-tier Machine Cores for these recipes. Check EMI or JEI for the exact component counts, as you will need one ring or motor block for every single block of your track's perimeter.
Tip: Automate plastic and bedrock extractor metal processing first, as expanding the ring later requires hundreds of metallic and polymer components.
3Lay Out the Closed-Loop Track
Place your Accelerator Controller down first, which acts as the item insertion and launch point. From the controller's exit port, build a continuous, hollow loop using Accelerator Ring blocks that eventually feeds directly back into the controller's input side. The track must be completely flat on the same Y-level and form a closed polygon using proper corner connections.
Tip: Use your Wrench to rotate misplaced ring blocks if the connected textures do not cleanly align around the corners.
4Integrate Accelerator Motors on Straightaways
Replace several standard Accelerator Ring blocks along the straight sections of your loop with Accelerator Motors. Motors are the active blocks that consume power to push the particle faster each time it passes through them. Never place motors directly on corners; keep them on long straight lines to maximize acceleration efficiency before the particle has to turn.
Tip: Start with 4 to 8 motors distributed evenly across your straight segments, then add more as your power grid grows.
5Configure theCollision Zone
To actually collide items, you have two design logic choices: a single-controller target loop or a dual-controller intersecting loop. For a standard single loop, the controller launches a payload around the ring until it hits the required velocity, then strikes the target item held inside the controller. For dual-ring setups, build two separate rings that share a collision chamber or intersect so two particles travelling in opposite directions smash into each other.
Tip: A single large ring is much easier to wire and power for beginners than synchronizing two intersecting rings.
6Wire the High-Voltage Power Grid
Connect Oritech Energy Pipes to the Accelerator Controller and every single Accelerator Motor in your loop. Because the Particle Accelerator draws massive bursts of energy during active acceleration cycles, hook the network up to a dedicated bank of high-tier energy storage units fed by large biofuel facilities, fossil fuel generators, or external mod reactors.
Tip: Oritech pipes are cached and fast with only one tier, so you do not need to worry about pipe bottlenecks—only your battery bank's total output rate.
7Insert Payloads and Execute a Collision
Open EMI/JEI and look up your desired Particle Accelerator recipe to note the two input items and the required collision velocity (measured in meters per second or Joules). Insert the primary reagent and target item into the Accelerator Controller—either manually or via Item Pipes. Once powered, the controller will inject the particle into the ring, where you can watch it visibly accelerate around the track until it reaches the threshold velocity and triggers the collision.
Tip: Install an Accelerator Sensor along the track if you want to measure current particle speed and emit a redstone signal for automated item feeding.
How it works
The Particle Accelerator operates on a kinetic physics loop rather than a standard progress bar. When an item is injected by the Accelerator Controller, it becomes a physical particle entity travelling through the hollow Accelerator Ring blocks. Every time the particle passes through a powered Accelerator Motor, kinetic energy is added, increasing its velocity.
However, corner turns introduce drag and velocity loss based on the sharpness and frequency of the turns relative to the straightaways. If a ring is too small, the friction from constantly turning corners will cap the particle's maximum speed, preventing it from ever reaching the velocity required for high-tier recipes no matter how many motors you add.
Once the accelerating particle reaches the target velocity defined by the recipe in EMI/JEI, the controller directs it into the target reagent. The kinetic energy converts into collision energy, consuming the two inputs to synthesize the exotic output item inside the controller's output slot (or transferring the raw collision energy into an adjacent Particle Collector for specialized energy-generation setups).
Common mistakes
- Building the ring too small: Compact 5x5 or 7x7 rings suffer from extreme cornering drag, making it physically impossible for particles to reach end-game velocity thresholds. Always build wide loops with long straightaways.
- Forgetting to power the Accelerator Motors: Only powering the Accelerator Controller will launch the particle at base speed, where it will quickly stall out. Every motor along the track needs an Energy Pipe connection.
- Starving the network mid-cycle: If your power buffers run dry while a particle is accelerating, the motors stop boosting and the particle decelerates due to track friction, wasting all the energy spent up to that point.
- Breaking the ring while active: Removing a ring block or controller while a high-speed particle is circulating will cause the particle to escape or abort the cycle, losing your inserted reagent.
FAQ
Why does my particle get stuck at a specific speed and never collide?
Your ring is either too small (corner friction is equal to motor acceleration) or you do not have enough powered Accelerator Motors on the straightaways. Expand the perimeter of the ring and add more motors.
How do I know the exact speed required for a specific crafting recipe?
Check the recipe in EMI, JEI, or the Oracle Index in-game book. Every Particle Accelerator recipe displays the two required input items alongside the minimum velocity or energy rating needed to fuse them.
Can I use power from other mods to run the Particle Accelerator?
Yes. Oritech natively supports standard modded energy systems on both Fabric and NeoForge (such as Mekanism, Powah!, Tech Reborn, and Ender IO), so you can connect external reactors directly to Oritech Energy Pipes or energy acceptors.
Do I need upgraded tiers of pipes to handle the accelerator's item and power needs?
No. Oritech is designed with a single, highly optimized tier for Item, Fluid, and Energy pipes. Standard Oritech Energy Pipes will transfer all the power your motors need as long as your storage batteries can supply it.
By combining a wide, flat loop of Accelerator Ring blocks with plenty of powered Accelerator Motors on the straightaways, you can push particles to extreme velocities and unlock all of Oritech's end-game collision recipes.