Flux Networks · Power · Intermediate
Flux Networks Priority, Limits, and Surge Mode Explained
Mastering the Flux Networks GUI allows you to construct a blackout-proof power grid across multiple dimensions without placing a single run of heavy cabling. By understanding how Priority, Transfer Limits, and Surge Mode interact, you can ensure critical base infrastructure stays online even when power-hungry machinery drains your energy reserves.
What you need
- Flux Plug (at least two, for primary and backup power generation)
- Flux Point (several, to distribute power to different base sectors)
- Basic, Herculean, or Gargantuan Flux Storage (for grid buffering)
- Flux Configurator (optional, for quick copying and pasting of node settings)
- An existing, named Flux Network with active energy generation
Step by step
1Name Your Nodes for Network Visibility
Right-click any deployed Flux Point or Flux Plug to open its Home tab. Click the top name field to rename the node based on its specific role, such as 'Life Support Point' or 'Quarry Point'. Press Enter to save the name so you can easily identify it later from the central network menu.
Tip: You can also change the node's display icon by clicking the item frame next to its name in the GUI.
2Tier Your Consumer Priorities
On a Flux Point attached to vital machinery like digital storage systems or fuel production, locate the Priority setting in the Home tab. Set this value to a high positive number, such as 100. Next, go to Flux Points powering heavy, non-essential machines like ore lasers or quarries, and set their Priority to a low or negative number, such as -50.
Tip: Keep standard crafting machines at the default Priority of 0 to establish a clear three-tier hierarchy: Critical (Positive), Standard (Zero), and Bulk (Negative).
3Configure Backup Generator Priorities
Priority also applies in reverse for energy extraction on Flux Plugs. Attach a Flux Plug to your renewable, primary power source (like solar or wind) and set its Priority to 50. Attach a second Flux Plug to a fuel-burning backup generator and set its Priority to 10 so the network only pulls from the backup when primary generation cannot keep up with demand.
4Throttle Power-Hungry Consumers
Open the GUI of a Flux Point connected to a machine that causes sudden power spikes. Locate the Transfer Limit field and type in a specific cap that is slightly lower than your base's total baseline generation. Make sure the limit toggle button next to the number is enabled so the restriction takes effect immediately.
Tip: Check JEI or your modpack's in-game guide to see the exact energy units your pack uses, as Flux Networks automatically converts between standard energy systems.
5Activate Bypass Limit for Uncapped Transfer
When feeding end-game energy sinks or rapid-charging stations, standard limits can bottleneck your progress. Open the target Flux Point or Flux Plug and toggle the 'Bypass Limit' option (often represented by an infinity symbol or dedicated toggle button). This completely removes the default transfer cap, allowing the node to move as much energy per tick as the connected machine or cable can accept.
Tip: Never enable Bypass Limit on a low-priority bulk machine unless your energy storage buffer is massive, or it will instantly drain your network.
6Deploy Surge Mode for Absolute Override
In an emergency where a specific node must receive or send power above all others without altering your complex number hierarchy, toggle on 'Surge Mode' in the node's Home tab. Surge Mode temporarily forces that Flux Point or Flux Plug to the absolute top of the network's priority queue, ignoring whatever numeric priority value is typed into the box.
Tip: Use Surge Mode on a Flux Point attached to base defense turrets during an attack to guarantee they never lose power.
7Audit and Remotely Manage via Network Connections
Open any Flux node and click the 'Network Connections' tab at the top of the GUI (the list icon). Here you can see every Flux Plug, Flux Point, and Flux Storage on your network across all dimensions. Click on any connection in this list to remotely adjust its Priority, Transfer Limit, or Surge Mode without having to travel to the node's physical location.
Tip: Hold Shift while clicking multiple connections in this tab to batch-edit their priority and limit settings all at once.
8Balance the Grid with Flux Storage
Place a Basic, Herculean, or Gargantuan Flux Storage block anywhere in your base and link it to your network. By default, Flux Storage acts as a middleman buffer, soaking up excess power from your Flux Plugs when machines are idle and discharging it to Flux Points when demand spikes. Check the 'Network Statistics' tab (the graph icon) to watch your input/output curves and ensure your buffer is holding steady.
Tip: If your Flux Storage is constantly draining your backup generators just to fill itself, make sure your backup Flux Plug priority is tuned properly or control the generator with a redstone comparator reading the Flux Storage block.
How it works
At the start of every server tick, a Flux Network calculates the total energy offered by all connected Flux Plugs and compares it to the total energy requested by all connected Flux Points. Instead of dividing insufficient power evenly across the whole base—which causes machines to stutter and digital storage systems to flicker offline—the network distributes energy strictly in descending order of Priority.
During each tick, the network satisfies the highest-priority Flux Points first. A node with Priority 100 will receive 100% of the energy it requests (up to its configured Transfer Limit) before a node with Priority 99 receives a single unit of energy. The same logic governs Flux Plugs: the network drains the highest-priority Flux Plugs completely before drawing power from lower-priority plugs.
Surge Mode and Bypass Limit act as rule-breakers within this math. Enabling Surge Mode moves a node into a special 'Tier 0' priority bracket above the highest possible numeric value. Meanwhile, Bypass Limit removes the internal safety ceiling on throughput, letting the mod transfer energy up to the maximum integer limit supported by the game's code, constrained only by the internal buffers of the machines touching the Flux nodes.
Common mistakes
- Enabling Surge Mode on every node thinking it makes energy move faster; if every Flux Point is in Surge Mode, none of them have priority, and a power deficit will cause a total base blackout.
- Putting Bypass Limit on a low-tier machine or cable without checking what is downstream; an uncapped machine array can instantly drain millions of energy units from your Flux Storage in a single tick.
- Forgetting to name Flux Points and Flux Plugs when placing them, resulting in a 'Network Connections' list full of identical unnamed coordinates that are impossible to troubleshoot remotely during a power crisis.
- Leaving wireless inventory charging enabled on the main network while carrying high-capacity batteries or endgame armor, which can silently siphon all power away from base machinery whenever your player takes damage or flies.
FAQ
What happens if two Flux Points have the exact same Priority number during a power shortage?
When two or more Flux Points share the exact same Priority value and there is not enough power to satisfy all of them, the network splits the remaining available energy equally among those tied nodes.
Why is my Flux Point still transferring slowly even though I turned on Bypass Limit?
A Flux Point can only push energy as fast as the receiving block can accept it. If your Flux Point is attached to a low-tier energy cable or a machine with a small internal energy buffer, that external block is the bottleneck, not the Flux Network.
How does Flux Storage fit into the Priority system?
Flux Storage blocks operate as an automatic network buffer that fills when generation exceeds machine demand and empties when demand exceeds generation. If you connect external batteries using a Flux Point and Flux Plug instead of native Flux Storage blocks, you must set the charging Point's priority lower than your Flux Plugs to prevent an infinite energy loop.
Can I copy priority and limit settings from one node to another without using the GUI?
Yes, craft a Flux Configurator. Shift-right-click a configured Flux Point or Plug to copy its settings, then right-click any other node to instantly paste the Priority, Limit, and network assignment.
By combining tiered numeric Priorities for daily operations, Transfer Limits for heavy consumers, and Surge Mode for critical overrides, you can build an intelligent Flux Network that guarantees your most important base systems never lose power.