Mekanism · End game
Mekanism Supercritical Phase Shifter Antimatter Facility
This endgame facility converts radioactive Nuclear Waste into Antimatter Pellets using a Solar Neutron Activator bank and the massive Supercritical Phase Shifter (SPS) multiblock. Building this array is mandatory for players looking to craft high-tier MekaSuit modules, the QIO storage network, and final-tier Mekanism utilities. Due to the immense energy demand of the SPS, this layout integrates a dedicated Induction Matrix buffer and high-tier logistics to ensure safe, uninterrupted production.
- Footprint
- 17x13x9 blocks
- Power
- Up to 400 MFE/t (Check JEI for exact per-mB Antimatter cost)
- Throughput
- 1 Antimatter Pellet per 1,000 mB Polonium
- Difficulty
- advanced
Flow diagram
How items, fluids and energy move through the setup, left to right.
Swipe sideways to see the whole diagram
Materials
| Item | Count |
|---|---|
| SPS Casing | 60 |
| SPS Port | 4 |
| Supercharged Coil | 2 |
| Structural Glass | 122 |
| Solar Neutron Activator | 4 |
| Chemical Crystallizer | 1 |
| Ultimate Pressurized Tube | 24 |
| Ultimate Universal Cable | 32 |
| Configurator | 1 |
| Speed Upgrade | 40 |
| Energy Upgrade | 40 |
Build it step by step
1Construct the SPS Frame
Build the 7x7x7 Supercritical Phase Shifter frame using SPS Casings. Leave the center 5x5 area on all six faces open for glass and ports, and ensure the corners and edges are solid SPS Casings. Refer to the Mekanism multiblock guide or JEI to confirm casing placement.
2Install Ports and Coils
Place four SPS Ports into the centers of the side faces: one for Polonium input, two for energy input, and one for Antimatter gas output. Inside the structure, attach Supercharged Coils directly onto the interior side of the two energy input SPS Ports.
3Seal the Multiblock
Fill all remaining open face blocks with Structural Glass or extra SPS Casings. Once the final block is placed, the structure will emit red particles indicating a valid multiblock formation. Use the Configurator to shift-right-click the output port to eject mode.
4Set Up the Solar Neutron Array
Place four Solar Neutron Activators nearby with an unobstructed view of the sky. Connect your Fission Reactor's waste pipe into the bottom of these machines using Ultimate Pressurized Tubes. Install Speed Upgrades into the activators to keep up with heavy reactor output.
5Route Polonium and Energy
Connect the front outputs of the Solar Neutron Activators to the Polonium input port on the SPS. Run thick lines of Ultimate Universal Cables from your Fusion Reactor or Induction Matrix directly into the two SPS Ports backed by Supercharged Coils.
6Crystallize the Antimatter
Place a Chemical Crystallizer adjacent to the SPS output port and link them with a pressurized tube. Power the Crystallizer and set its side configuration to auto-eject items into an adjacent chest or QIO Exporter.
How it works
The process begins with Nuclear Waste piped safely out of an active Fission Reactor. Because Nuclear Waste is hazardous and cannot be teleported via Quantum Entangloporters, this facility must be built locally near your reactor zone. The Solar Neutron Activators use direct sunlight to convert the Nuclear Waste into Polonium gas at a 1:1 ratio.
Once Polonium enters the Supercritical Phase Shifter, the Supercharged Coils dump massive amounts of Forge Energy into the gas, ionizing and shifting it into Antimatter gas. The conversion ratio is steep—requiring 1,000 mB of Polonium and hundreds of millions of FE to generate just 1 mB of Antimatter gas (check JEI for your modpack's exact power multiplier). Because Polonium is also radioactive, keeping the pipes short and buffered prevents bottlenecks.
Finally, the resulting Antimatter gas is non-radioactive and stable. It is piped directly into a Chemical Crystallizer, which solidifies 1,000 mB of Antimatter gas into a single solid Antimatter Pellet ready for the Antiprotonic Nucleosynthesizer or MekaSuit Modification Station.
Upgrades and scaling
- Add more SPS Ports with internal Supercharged Coils to bypass cable transfer limits and feed even more power from a Fusion Reactor.
- Build the Solar Neutron Activator array in a permanent daylight dimension or sleep through the night automatically to prevent Polonium conversion pauses.
- Attach a Quantum Entangloporter to the Antimatter gas output line to transmit the safe gas back to your main base for crystallization.
Common mistakes
- Breaking a pipe containing Nuclear Waste or Polonium; always let the system completely drain into the SPS before modifying the pressurized tubes to avoid catastrophic radiation leaks.
- Placing the Supercharged Coils on the wrong interior blocks; each coil must be directly attached to the inside face of an SPS Port receiving power.
- Using low-tier Universal Cables that bottleneck the massive FE/t throughput required by the Supercharged Coils.
- Trying to pipe Spent Nuclear Waste into the system instead of standard Nuclear Waste from the Fission Reactor.
FAQ
Why isn't my Supercritical Phase Shifter forming?
Ensure the outer 7x7x7 edges are strictly SPS Casings, while Structural Glass and SPS Ports are only placed within the inner 5x5 faces. Also ensure no extra blocks besides Supercharged Coils are inside the hollow interior.
Can I teleport Polonium into the SPS using a Quantum Entangloporter?
No. Mekanism blocks all radioactive gases, including Nuclear Waste and Polonium, from entering Quantum Entangloporters. You must use Pressurized Tubes.
Will the SPS explode if it runs out of power or overfills?
No. Unlike the Fission Reactor, the SPS is completely safe and will simply pause operations if power drops or if the internal Antimatter tank fills up.