XNet · Addon guide · Intermediate

YNot Addon Guide: Routing Mana, Essentia, and Mek Gases in XNet

Moving Botania Mana, Thaumcraft Essentia, and Mekanism Gases usually requires three entirely different sets of pipes, tubes, and sparks that quickly clutter your base. By installing the YNot addon for XNet in 1.12.2 modpacks, you can consolidate all of these exotic resources into a single, lag-free network. This guide will walk you through setting up dedicated XNet channels to route magic and industrial gases alongside your standard items and power.

What you need

  • XNet Controller
  • Network Cables (any color)
  • Connectors or Advanced Connectors (matching your cable color)
  • A Forge Energy (FE/RF) power source to run the Controller
  • YNot mod installed (alongside Botania, Thaumcraft, or Mekanism)
  • Source and destination blocks (e.g., Mana Pools, Warded Jars, Electrolytic Separators)

Step by step

  1. 1Power the XNet Controller

    Place your XNet Controller near your crafting area and hook it up to an active Forge Energy source. Attach a Connector directly to the Controller and run Network Cables to your various magic and tech machines. Remember that the Controller itself requires a small, continuous trickle of power to operate its active channels.

    Tip: Use Advanced Connectors whenever possible; they allow higher transfer rates and provide access to any side of a block remotely.

  2. 2Connect Your Machines and Containers

    Place regular or Advanced Connectors directly against the blocks you want to network. For Botania, attach connectors to Mana Pools or Spreaders; for Thaumcraft, connect to Essentia Smelteries, Alembics, and Warded Jars; for Mekanism, connect to the exact face of the machine configured for gas input or output. Open the Controller GUI to verify all attached blocks appear in the device list on the left.

    Tip: Rename your connectors in the Controller GUI (e.g., 'Mana In', 'Oxygen Out') so you do not lose track of which machine is which.

  3. 3Configure a Mekanism Gas Channel

    In the Controller GUI, click on an empty channel column at the top and change its channel type to 'ynot.mekgas' (or Mekanism Gas, depending on your version). Click the junction box connecting your gas-producing machine (like an Electrolytic Separator) to this channel and set its mode to 'Extract'. Next, click the junction box for your destination machine (like a Purification Chamber) and set it to 'Insert'.

    Tip: You can filter specific gases by placing a Gauge Dropper or a filled Gas Tank containing the desired gas into the filter slot of the Extract or Insert configuration.

  4. 4Route Botania Mana Without Sparks

    Select a new empty channel column and set the type to Botania Mana. Create a connector node for your generating Mana Pool and set it to 'Extract', then create a node for your receiving Mana Pool, Runic Altar, or Botanical Brewery and set it to 'Insert'. You can adjust the operation speed in ticks to control how fast the pool drains.

    Tip: XNet cannot pull directly from Generating Flora like Endoflames; you must still use a Mana Spreader to shoot mana into an initial buffer Mana Pool before XNet can extract it.

  5. 5Automate Thaumcraft Essentia

    Select another empty channel and set its type to Thaumcraft Essentia. On the Alembics or Essentia Smeltery connector, create a node and set it to 'Extract', lowering the tick rate if you want faster draining. On your bank of Warded Jars or Essentia Reservoirs, create 'Insert' nodes to automatically sort the slurry without ever dealing with suction.

    Tip: To lock an Insert node to a specific aspect, drag a Phial of Essentia or a Crystal Essence of that aspect from JEI (or your inventory) into the node's filter slot.

  6. 6Fine-Tune Priorities and Rates

    Review your active nodes and set priority numbers on the 'Insert' tabs if you have multiple destinations for the same resource. Higher priority numbers receive resources first, which is ideal for sending Void Jars a lower priority than regular Warded Jars. Check the transfer rates and tick intervals in the GUI—refer to JEI or your pack's config if the default transfer limits feel throttled.

    Tip: Setting the extract operation time to 10 or 20 ticks on passive setups saves a tiny bit of server performance compared to checking every single tick.

How it works

Standard pipes, Essentia Tubes, and Pressurized Tubes work by turning every single segment of pipe into a ticking Tile Entity that constantly checks its neighbors to push or pull contents. XNet bypasses this entirely: its Network Cables are dumb blocks with no tile entity data, meaning a cable spanning thousands of blocks generates zero lag.

The YNot addon acts as a translation bridge between the APIs of other mods and the XNet Controller. Instead of simulating Thaumcraft's directional suction or Botania's line-of-sight mana bursts, the Controller simply queries the attached Connectors every few ticks. If an Extract node finds a valid capability (like an Essentia container or a Mekanism Gas handler) and an Insert node has room, the Controller teleports the resource instantly from point A to point B.

Because XNet handles all the routing math inside the Controller GUI, it ignores the native limitations of the target mods. You never get Essentia tube jamming from competing suction types, and Mekanism gases can share the exact same block space as your item and energy cables.

Common mistakes

  • Ignoring Mekanism Side Configurations: Mekanism machines strictly enforce sided I/O for gases. If a machine's side is set to eject gas only from the left, placing a standard XNet Connector on the back will fail. Either reconfigure the machine's 'Gases' tab in its GUI, or use an XNet Advanced Connector which lets you digitally spoof which side of the block you are accessing.
  • Connecting directly to Botania Flowers: Trying to extract mana straight from a functional or generating flower will not work because flowers use an internal collector/receiver logic rather than a standard storage buffer. Always route from a Mana Spreader into a Mana Pool first, and let XNet handle distribution from that pool.
  • Forgetting Void Jar Priorities: If you hook up normal Warded Jars and Void Jars to the same Essentia channel without setting priorities, XNet may dump valuable Essentia straight into the Void Jar first. Always set your normal Warded Jars to a higher priority (e.g., 10) and your Void Jars to a lower priority (e.g., 0).
  • Letting the Controller lose power: If your base experiences a power brownout and the XNet Controller drains its internal FE buffer, all Mana, Gas, and Essentia routing stops instantly. Put your Controller on a dedicated battery backup so critical systems (like Mekanism Fission Reactor cooling gases) never halt.

FAQ

Can I transport Mekanism Slurries (from 5x ore processing) using YNot?

Yes, Mekanism classifies clean and dirty ore slurries under its internal Gas system. You can route them through a Mekanism Gas channel just like Oxygen or Hydrogen.

Why isn't my Thaumcraft Infusion Matrix pulling Essentia through XNet?

The Runic Matrix pulls Essentia wirelessly from nearby jars using its own internal mechanic during crafting; it does not have a fluid-style inventory you can pump into. Use XNet to keep the Warded Jars around your altar full, and let the Matrix draw from the jars normally.

How fast can XNet transfer Botania Mana compared to Sparks?

Transfer rates depend heavily on the modpack's configuration files and whether you use normal or Advanced Connectors. Generally, an upgraded XNet channel is much faster than basic Mana Spreaders, though a Spark with a Dominant/Recessive augment is still faster for massive endgame Terrasteel crafting.

Do I need different colored cables to separate Gases, Mana, and Essentia?

No. Cable colors only exist to keep two entirely separate XNet networks from merging if their cables touch. A single color of cable can carry items, energy, fluids, gases, mana, and essentia simultaneously across its eight internal Controller channels.

With the YNot addon, your XNet Controller becomes the ultimate universal logistics hub, cleanly automating Botania Mana, Thaumcraft Essentia, and Mekanism Gases over a single cable line without the headache of suction or sided pipe clutter.

More XNet guides

XNet · PowerHow to Build a Lag-Free Power Grid with XNetIn this guide, you will learn how to build an ultra-efficient, centralized power distribution grid using XNet to send Forge Energy (FE) or Redstone Flux (RF) from your generators to all of your machines. Unlike traditional energy conduits that constantly calculate paths and cause server lag, XNet uses a single Controller and lightweight cables to move power instantly across huge distances. By the end, you will have a self-sustaining network that powers your entire base and keeps its own brain running smoothly.Beginner7 steps
XNet · Setup guideHow to Set Up Item and Fluid Routing in XNetIn this guide, you will learn how to build a lag-free, automated item and fluid sorting network using XNet. Mastering XNet routing allows you to organize massive storage rooms and processing lines through a single cable line, replacing messy spaghetti pipes with clean, intelligent distribution logic.Intermediate7 steps
XNet · AutomationHow to Automate Ore Processing with a Single XNet CableLearn how to automate a complete ore-doubling and smelting production line using a single row of XNet cables. Instead of running separate pipes for energy, input items, and output items, you will use one Advanced Connector per machine to handle power, ore insertion, and ingot extraction simultaneously. This approach eliminates cable spaghetti, saves space, and drastically reduces server lag.Intermediate7 steps
XNet · AutomationHow to Use XNet for Clean AE2 & Refined Storage SubnetsAutomating complex machines like Applied Energistics 2 Inscribers or multi-input alloy furnaces often creates a chaotic mess of power, item, and data cables. By pairing an XNet Controller with a single Crafting Interface or Crafter, you can condense all item routing, side-specific insertion, and power delivery into one clean block line. This advanced guide will walk you through building a lag-free, single-cable XNet subnet to handle your most complicated processing chains.Advanced7 steps
XNet · Addon guideXNet Gases Guide: How to Route Mekanism Gases & ChemicalsSetting up Mekanism's multi-tier ore processing usually results in a messy nightmare of Pressurized Tubes, Universal Cables, and Logistical Transporters. By using XNet along with the XNet Gases addon, you can condense your entire 3x or 4x ore processing line—including Oxygen, Hydrogen Chloride, and Slurries—into a single, lag-free cable behind your machines. This guide will walk you through routing Mekanism gases and chemicals cleanly using an XNet Controller and Advanced Connectors.Intermediate7 steps
XNet · TroubleshootingXNet Troubleshooting Guide: Fixing Common Network & Connector IssuesSetting up an XNet network is one of the most lag-free ways to automate your base, but a single misconfigured block can halt your entire production line. This troubleshooting guide will teach you how to diagnose and fix the most common XNet errors, including missing connectors, machine sidedness lockouts, and router conflicts. Mastering these core logic rules ensures your items, fluids, and energy flow smoothly without frustrating bottlenecks.Beginner6 steps