Storage Drawers · Setup guide · Intermediate
How to Build a Drawer Controller Storage Network
A Drawer Controller Storage Network centralizes your entire wall of drawers into a single access point for both manual dumping and automated piping. By combining the Drawer Controller with Trim blocks and Controller Slaves, you can build an expansive, room-spanning storage system that organizes your inventory with a single double-click. This guide will walk you through constructing the physical network, bridging structural gaps, and setting up secondary automation ports.
What you need
- 1 Drawer Controller
- Several Drawers (any wood type, size 1x1, 1x2, or 2x2) or Compacting Drawers
- Trim blocks (Oak Trim, Spruce Trim, etc., matching your aesthetic)
- 1 or more Controller Slaves (optional, for expanded automation)
- 1 Drawer Key (highly recommended for locking drawers)
- Hoppers, pipes, or external storage buses for testing automation
Step by step
1Place the Central Drawer Controller
Choose a central, easily accessible spot in your storage room and place your Drawer Controller block. Ensure the textured front face is pointing outward toward where you will stand. This block will serve as the brain of your network and your primary manual drop-off point.
Tip: Place the controller at eye level so you can easily double-right-click it when returning from mining trips.
2Connect Your First Bank of Drawers
Place your standard Drawers or Compacting Drawers directly adjacent to the Drawer Controller. You can place them on the left, right, top, bottom, or back of the controller. As long as each new drawer touches a face of the controller or another already-connected drawer, it joins the network.
Tip: You can mix and match 1x1, 1x2, 2x2, and Compacting Drawers freely within the same connected wall.
3Bridge Gaps Using Trim Blocks
If you want to wrap your storage around a corner, cross a hallway, or leave space for pillars without breaking the network, place Trim blocks. Connect a Trim block to a connected drawer, run a continuous line of Trim around the obstacle, and place your next group of drawers touching the end of the Trim line. The controller treats Trim as a conductive wire for the storage network.
Tip: Trim blocks are much cheaper to craft than actual drawers and do not generate tile-entity lag, making them ideal for hidden floor or ceiling wiring.
4Add Controller Slaves for Automation
Place a Controller Slave block anywhere so that it touches a connected drawer or Trim block in your network. While the main Drawer Controller is best kept clear in the front for manual player use, you can tuck Controller Slaves behind walls or under floors. Attach your hoppers, mod pipes, or external storage cables directly to the faces of the Controller Slave.
Tip: A single network can only have one main Drawer Controller, but it can support multiple Controller Slaves to give you dozens of piping faces.
5Pre-Assign and Lock Your Drawers
Before dumping items into the system, insert at least one of each desired item into the specific drawers where you want them stored. Craft a Drawer Key and right-click the drawers (or the Drawer Controller itself to affect the whole network at once) to lock them. A small golden lock icon will appear on the drawer frames.
Tip: Locking drawers prevents the controller from filling empty slots with random mob drops or unstackable gear when you mass-deposit items.
6Deposit Items via the Controller
Hold an item you want to store and right-click the front face of the Drawer Controller to insert that stack into the network. To dump your entire inventory of matching items, quickly double-right-click the front of the Drawer Controller. The controller will automatically scan your hotbar and inventory, pulling out every item that matches a drawer in the connected network.
Tip: You can double-right-click with an empty hand or any random tool to trigger the full-inventory sweep for all matching items.
How it works
The Drawer Controller operates using a contiguous block-search algorithm within a fixed bounding box. Periodically, and whenever adjacent blocks update, the controller scans outward from itself along touching block faces (up, down, north, south, east, west). If it finds a valid Storage Drawers network component—specifically any Drawer, Compacting Drawer, Trim, or Controller Slave—it adds that block to its internal routing table and continues scanning from that block.
This search is restricted by a maximum range radius (typically around 12 blocks in any cardinal direction from the controller, though you should check your modpack config or in-game documentation if it feels smaller or larger). A block is only part of the network if it is both within this geometric bounding box AND has an unbroken chain of face-to-face connections back to the controller. Diagonal connections do not count.
When you double-right-click the controller or pump items into a Controller Slave, the controller checks its routing table sequentially. It prioritizes drawers that already contain the incoming item (or locked drawers assigned to that item) before attempting to route items into completely empty, unlocked drawers. Controller Slaves act as direct proxy extensions of the controller's inventory capability, exposing the exact same unified inventory slots to external pipes and hoppers without executing their own separate network scans.
Common mistakes
- Connecting two Drawer Controllers to the same network: Having two main controllers touching the same group of drawers causes inventory conflicts and rapid lag as they fight over routing. Use one Drawer Controller and multiple Controller Slaves instead.
- Relying on diagonal corner connections: Placing drawers touching only at their diagonal edges breaks the connection chain. Always place a Trim block or another drawer in the inner corner so the blocks share full flat faces.
- Building beyond the controller's maximum radius: Even if your chain of Trim and drawers is unbroken, any drawer placed outside the controller's maximum coordinate radius will simply be ignored. Place your controller in the physical center of your storage room rather than at the far end.
- Pumping items into an unlocked network: If you attach a quarry or farm pipe to a Controller Slave while you have empty, unlocked drawers, overflow trash items will quickly claim those empty drawers and ruin your organization. Always lock your network with a Drawer Key first.
FAQ
Can I extract items manually by clicking the Drawer Controller?
No. The Drawer Controller only accepts manual item insertion via right-click or double-right-click. To take items out by hand, you must walk up to the specific drawer and left-click (for one item) or shift-left-click (for a full stack). However, pipes and hoppers CAN extract items from the controller or Controller Slaves.
Why are my Controller Slaves not accepting items from hoppers?
Verify that the Controller Slave is physically touching a drawer or Trim block that leads back to an active Drawer Controller within range. A Controller Slave has no brain of its own; without a valid connection to a main Drawer Controller, it acts as an inert block.
Do Trim blocks have to match the wood type of my drawers?
No. You can connect Oak Drawers using Spruce Trim or any framed variant. The network logic only checks if the block is a valid Trim tile, completely ignoring wood species or custom framing textures.
How do I upgrade the capacity of the network?
You cannot put storage upgrades inside the Drawer Controller itself. Instead, shift-right-click individual drawers with an empty hand to open their upgrade UI (or right-click them directly with an upgrade item) to boost the capacity of specific high-volume slots.
By placing a central Drawer Controller, bridging gaps with face-connected Trim blocks, locking slots with a Drawer Key, and exposing Controller Slaves to your pipes, you create a lag-friendly and effortless bulk storage system.