LaserIO · Setup guide · Intermediate
How to Automate Ore Processing on a Single Block Face with LaserIO
Tired of spaghetti piping cluttering your modded Minecraft base? This intermediate guide teaches you how to use LaserIO to supply power, pump fluids, insert raw ores, and extract finished products through a single block face of your processing machine. Mastering this technique will drastically shrink your factory footprint and simplify complex automation setups.
What you need
- 2x Laser Nodes
- 1x Laser Wrench
- 2x Item Cards
- 2x Fluid Cards
- 2x Energy Cards
- 1x Basic Filter (optional, depending on your machine's internal side routing)
- An ore processing machine that requires power and fluid (plus an external power source, fluid tank, input chest, and output chest)
Step by step
1Place and Link Your Laser Nodes
Place one Laser Node directly behind your ore processing machine, leaving the front and sides completely clear. Place a second Laser Node next to your resource hub—ideally positioned so its different faces touch your input chest, output chest, fluid tank, and energy cell. Equip your Laser Wrench, shift-right-click the first node, and then right-click the second node to establish a wireless laser connection between them.
Tip: Laser Nodes can connect through solid walls as long as they are within the default range; check the in-game Patchouli book or JEI for exact distance limits.
2Prepare the Machine-Side Interface
Right-click the Laser Node behind your processing machine to open its GUI. At the top, you will see directional tabs corresponding to the six block faces (North, South, East, West, Up, Down). Select the tab that corresponds to the face actually touching your machine. You will now see a 3x3 grid capable of holding up to nine different logistics cards for that single block face.
Tip: If you aren't sure which direction your machine is facing, look directly at the machine from the node's position and check the cardinal direction on your F3 debug screen.
3Configure Energy and Fluid Insertion
Right-click an Energy Card and a Fluid Card while holding them in your hand to open their respective configuration GUIs. Click the mode button at the top left of each card until they both read 'Insert', leaving their default channel colors set to white. Place both of these configured cards into the 3x3 grid of the machine's directional tab inside your Laser Node.
Tip: You can shift-right-click a card inside the node's GUI to open its settings directly without pulling it back into your inventory.
4Configure Raw Ore Insertion and Ingot Extraction
Open one Item Card, set its mode to 'Insert' on the white channel, and place it into the same 3x3 grid on the machine's node. Open your second Item Card, set its mode to 'Extract', and change its channel color to orange so it doesn't conflict with your inputs. Place a Basic Filter into this Extract card, whitelist your processed ingots (or crushed ore), and place the card into the remaining space of that same directional tab.
5Set Up the Resource Hub Node
Move over to your second Laser Node at the resource hub and open its GUI. Unlike the machine node where everything went into one tab, here you will select the specific directional tab for each adjacent storage block. Place an Energy Card set to 'Extract' (white channel) in the tab facing your battery, and a Fluid Card set to 'Extract' (white channel) in the tab facing your water or chemical tank.
6Finalize Item Routing at the Hub
In the hub node, select the directional tab facing your raw ore input chest and insert an Item Card set to 'Extract' on the white channel. Finally, select the tab facing your finished product chest and insert an Item Card set to 'Insert' on the orange channel. The moment you place the final card, you will see colored laser beams appear, and your machine will immediately begin receiving power, fluid, and raw ores while exporting finished products—all from its back face.
Tip: If the default transfer speeds are too slow for your setup, craft Card Overclockers and insert them directly into the cards to boost throughput and reduce tick delay.
How it works
Traditional pipe mods require dedicated block faces because the pipe itself acts as a single-purpose conduit—an item pipe cannot carry fluid, and a fluid pipe cannot carry Forge Energy. LaserIO completely bypasses this limitation by separating the physical block (the Laser Node) from the transfer logic (the Cards). The node simply acts as a multi-slot dock that talks to adjacent inventories.
Because each directional tab in a Laser Node has a 3x3 inventory, the mod can evaluate up to nine independent transfer instructions on a single block face every cycle. When you put an Energy Insert, Fluid Insert, Item Insert, and Item Extract card into the same tab, the node queries the machine's capabilities for power, fluid tanks, and item slots simultaneously through that one shared face.
The color-coded channel system acts as a virtual routing network inside the laser beam. By putting your raw ore extraction and machine insertion on the white channel, and your product extraction and chest insertion on the orange channel, both item streams travel through the exact same nodes without ever mixing or causing a feedback loop.
Common mistakes
- Forgetting to configure the machine's internal side settings: Many tech mod machines lock specific faces to input-only or output-only by default. Make sure you open your processing machine's own GUI and set the back face to allow both input and output for items, fluids, and energy.
- Putting cards in the wrong directional tab: If you place your cards into the 'North' tab of the Laser Node when your machine is actually to the 'South', nothing will happen. Always verify your cardinal directions.
- Mismatched color channels: An 'Extract' card on the white channel will only ever send resources to an 'Insert' card on the white channel. If your items aren't moving, double-check that the extract and insert cards share the exact same color square.
- Creating an infinite loop on the same face: If you put an Item Insert card and an Item Extract card on the same block face using the same color channel without filters, the node will endlessly insert and pull the same raw ore. Always separate input and output channels by color and use Basic Filters.
FAQ
Can I combine all my cards easily, or do I need a huge inventory to carry them?
You can craft a Card Holder! When placed in your inventory or Curios slot, it automatically stores piles of cards, filters, and overclockers in a dedicated pouch, pulling them out seamlessly when you configure nodes.
What if my machine doesn't allow input and output on the same side in its own settings?
Inside the LaserIO Card GUI, there is a 'Sneaky' directional setting (set to 'Default' initially). You can change this setting to 'Up', 'Down', or any cardinal direction, which tricks the adjacent machine into thinking the items or fluids are entering from a completely different side while still only physically touching one face.
How do I speed up energy, fluid, or item transfer rates?
Craft Node Overclockers and Logical Overclockers (or Card Overclockers depending on your mod version). Opening a card's GUI reveals slots where you can insert overclockers to drastically increase the items per operation and reduce the ticks between operations.
By combining directional tabs, multi-type logistics cards, and color-coded channels inside a single Laser Node, you can cleanly automate complex multi-input machines using only one block face.