XNet · Early game
Single-Cable 3x Ore Processing Line
Eliminate early-game cable spaghetti by routing energy, fluids, gases, and items through a single network line using XNet. This setup achieves full 3x ore processing with Mekanism machines in a flat, wall-friendly footprint. By using a single Controller and hidden connectors, you save valuable early resources and keep your base looking completely clean.
- Footprint
- 6x2x2 blocks
- Power
- ~400 FE/t at full load (check JEI for modpack tweaks)
- Throughput
- ~1 raw ore per 3 seconds
- Difficulty
- beginner
Flow diagram
How items, fluids and energy move through the setup, left to right.
Swipe sideways to see the whole diagram
Materials
| Item | Count |
|---|---|
| Controller (XNet) | 1 |
| Connector (Blue) | 10 |
| Network Cable (Blue) | 12 |
| Facade | 10 |
| Electrolytic Separator | 1 |
| Purification Chamber | 1 |
| Crusher | 1 |
| Enrichment Chamber | 1 |
| Energized Smelter | 1 |
| Chest | 2 |
| Water Source Block or Sink | 1 |
Build it step by step
1Place the Machine Line
Place your five processing machines in a single horizontal row from left to right: Electrolytic Separator, Purification Chamber, Crusher, Enrichment Chamber, and Energized Smelter. Place the XNet Controller directly to the left of the Separator. Put your Input Chest on top of the Controller and the Output Chest on top of the Smelter.
2Run the Single XNet Cable
Behind the line of machines and chests, attach a Blue Connector to the back face of every machine, both chests, the Controller, your power source, and your water source. Link all of these Connectors together using standard Blue Network Cables so they form one continuous backbone.
3Configure Machine Sides
Open the GUI for your Mekanism machines and head to the Side Config tab. For the Purification Chamber, Crusher, Enrichment Chamber, and Smelter, set the Back side to 'Input/Output' for Items and 'Input' for Energy. On the Electrolytic Separator, set the Right side to 'Output (Gas)' for Oxygen, and on the Purification Chamber, set the Left side to 'Input (Gas)' so oxygen transfers directly without needing gas pipes.
4Setup Channel 1 for Energy
Open the XNet Controller GUI. In Channel 1, select 'xnet.energy' as the channel type. Click the intersection for your power source and create an 'Extract' node, then click the intersections for the Controller and all five Mekanism machines to create 'Insert' nodes.
5Setup Channel 2 for Water
In Channel 2, select 'xnet.fluid' as the channel type. Create an 'Extract' node on your water source block or pump and set its rate to maximum. Create an 'Insert' node on the Electrolytic Separator, and remember to set the Electrolytic Separator's Hydrogen tank to 'Dump Excess' in its internal GUI.
6Setup Channel 3 for Items
In Channel 3, select 'xnet.item' as the channel type and set the distribution mode to 'Round Robin' or 'First Match'. Create 'Extract' and 'Insert' nodes to chain your items along the line. Use item filters on each 'Insert' node (Raw Ores into Purification, Clumps into Crusher, Dirty Dusts into Enrichment, Clean Dusts into Smelter) so items never enter the wrong machine.
7Apply Facades
Craft XNet Facades and combine them inside a Crafting Table with your base's wall or floor block to paint them. Shift-right-click the painted Facades directly onto the Connectors and Network Cables to completely hide the wiring behind a solid wall.
How it works
Traditional early-game setups require at least three distinct cable lines running behind your machines: energy cables, fluid pipes, and item transporters. XNet consolidates all of these into a single block space. The Controller acts as the brain of the operation, reading the inventories and buffers of every block attached to a Connector and executing transfers in batches.
Because standard XNet does not natively handle Mekanism gases without an extra addon mod, this design places the Electrolytic Separator directly adjacent to the Purification Chamber. By setting the Separator to auto-eject gas to its right, Oxygen pushes directly into the Purification Chamber while XNet handles the water input and power via the rear connector.
Item movement happens entirely inside Channel 3 using explicit filters. Since the rear faces of the Mekanism machines are configured as combined Input/Output ports, XNet can extract a finished product (like an Ore Clump) and immediately route it to the next machine's insert filter on the exact same tick, keeping the footprint minimal.
Upgrades and scaling
- Swap the standard Connectors on the machines for Advanced Connectors to unlock faster energy transfer rates and access different block faces remotely, allowing you to hide the cable line completely underground.
- Install Mekanism Tier Installers (Basic, Advanced, Elite, Ultimate) directly onto the four processing machines to transform them into Factories, tripling or quintupling your parallel ore throughput without changing a single XNet wire.
- If your modpack includes the XNet Gases addon, you can separate the Electrolytic Separator from the line and route the Oxygen through Channel 4, allowing you to use the leftover Hydrogen for an early Gas-Burning Generator.
Common mistakes
- Forgetting to power the XNet Controller itself. The Controller requires a small amount of constant FE to function, which is why you must add an Energy Insert node for the Controller on Channel 1.
- Failing to set item filters on the Channel 3 Insert nodes. Without filters, XNet will attempt to shove Clumps back into the Purification Chamber or send Raw Ores straight to the Output Chest.
- Leaving the machine sides on separate 'Input' and 'Output' faces instead of the combined 'Input/Output' (purple) setting. Since a standard Connector only touches the back face, it needs permission to both push and pull from that single side.
- Not setting the Electrolytic Separator to 'Dump Excess' on the Hydrogen side. Once the internal Hydrogen tank fills up, the machine stops producing Oxygen and your entire ore line will stall.
FAQ
Why isn't my XNet Controller moving any items or power?
Check the top right of the Controller GUI to see if it has energy. You must create an Energy Insert node for the Controller itself on your energy channel so it can power its own internal operations.
Can I mix different cable colors in this setup?
Colors in XNet are used to keep separate networks from connecting when placed side-by-side. For this single-line build, stick to one color (like Blue) so all Connectors link to the same Controller.
How do I increase the item extraction speed in XNet?
Click on any Item Extract node in the Controller GUI and change the stack size from 'Single' to a higher number, or decrease the tick interval (especially when upgrading to Advanced Connectors).