LaserIO · Early game
Single-Block Machine Array Automation
This setup utilizes LaserIO to route items, fluids, and energy through the exact same block face of your processing machines. By eliminating bulky cable spaghetti, you can build ultra-compact, flush-to-the-wall machine arrays even in the early game. Each Laser Node acts as a multi-purpose conduit, handling inputs and outputs simultaneously without needing access to multiple sides of your machines.
- Footprint
- 5x3x2 blocks
- Power
- 0 FE/t (LaserIO networks do not consume power to operate)
- Throughput
- 8 items per 20 ticks baseline (scalable with Node Overclockers; check JEI for exact tiers)
- Difficulty
- beginner
Flow diagram
How items, fluids and energy move through the setup, left to right.
Swipe sideways to see the whole diagram
Materials
| Item | Count |
|---|---|
| Laser Node | 3 |
| Laser Wrench | 1 |
| Card Holder | 1 |
| Card Cloner | 1 |
| Item Card | 6 |
| Fluid Card | 3 |
| Energy Card | 3 |
| Basic Filter | 2 |
| Chest | 2 |
Build it step by step
1Place Inventories and Machines
Set up a row containing your Input Chest, Output Chest, Water Source Tank, and Early Power Generator. Leave a one-block gap, then place your two Processing Machines side by side. Note which faces of the machines and chests will be touching the Laser Nodes.
2Install and Link Laser Nodes
Place one Laser Node (I/O Node) so it touches the Input Chest, Output Chest, Tank, and Generator on different faces. Place two more Laser Nodes directly behind Processing Machine 1 and Processing Machine 2. Equip your Laser Wrench, shift-right-click the I/O Node, and right-click the Machine 1 Node to link them with a red laser beam, then link Machine 1 Node to Machine 2 Node.
3Configure the I/O Node Cards
Open the I/O Laser Node and select the tab corresponding to the Input Chest face; insert an Item Card set to Extract Mode (Orange Channel). On the Tank face tab, insert a Fluid Card set to Extract Mode (Orange Channel). On the Generator face tab, insert an Energy Card set to Extract Mode (Orange Channel).
4Configure the Output Path
Still inside the I/O Laser Node, switch to the tab corresponding to the Output Chest face. Insert an Item Card and click its mode button until it is set to Insert Mode. Change its color channel to Blue so it never mixes with your incoming raw materials.
5Configure Machine 1 Multi-Face Insertion
Open the Machine 1 Laser Node and select the tab facing Processing Machine 1. Insert one Item Card, one Fluid Card, and one Energy Card into this exact same directional tab. Set all three cards to Insert Mode on the Orange Channel so the machine receives items, water, and power through a single block face.
6Add Filtered Machine Extraction
In the same directional tab on the Machine 1 Laser Node, insert a second Item Card. Set this card to Extract Mode and change its color channel to Blue. Open the card's UI, place a Basic Filter inside, and whitelist your final processed items so the card does not accidentally pull out raw ingredients.
7Clone Settings to Machine 2
Use the Card Cloner to copy the configured cards from Machine 1 Node, or replicate the exact same four-card setup inside the Machine 2 Laser Node on the tab facing Processing Machine 2. Both machines will now share the network's inputs and push finished products back to the Output Chest.
How it works
Each Laser Node in LaserIO features six directional tabs inside its GUI, representing the six cardinal directions (North, South, East, West, Up, Down). Because each tab can hold up to nine independent cards, a single face of a Laser Node can interact with an adjacent machine in nine different ways simultaneously. By placing an Item Card, Fluid Card, and Energy Card all set to Insert Mode into the same tab, the node pushes all three resource types into a single face of the adjacent machine.
To prevent raw materials from looping directly into the Output Chest, the network uses color-coded channels. The I/O Node extracts raw materials on the Orange Channel, and the Machine Nodes only listen to the Orange Channel for insertion. Once a machine finishes processing, a second Item Card on the exact same machine face extracts the finished product onto the Blue Channel, which connects exclusively to the Insert Card waiting at the Output Chest.
Upgrades and scaling
- Craft and insert Card Overclockers into your Item, Fluid, and Energy Cards to dramatically increase transfer amounts and decrease the tick delay between operations (check JEI for recipe requirements).
- Add Node Overclockers into the side upgrade slots of your Laser Nodes to allow more cards to operate within the exact same game tick.
- Switch the Item Extract card on the I/O Node to Round Robin mode so raw materials are split completely evenly between Machine 1 and Machine 2.
- Replace the Basic Filter with a Tag Filter or Mod Filter if your processing array handles dozens of different ore types.
Common mistakes
- Forgetting to configure the adjacent machine's internal side-configuration UI to allow both inputs and outputs on the back face touching the Laser Node.
- Leaving both the input Item Card and output Item Card on the default Orange Channel, which causes the node to immediately extract raw materials out of the machine and dump them into the Output Chest.
- Inserting cards into the wrong directional tab inside the Laser Node GUI ( look at the floating cardinal direction letters inside the world block or use the colored side indicators to find the right tab).
- Exceeding the 8-block maximum laser connection range between two Laser Nodes without placing an intermediate relay node.
FAQ
Why isn't my machine accepting items, fluids, and power on the same side?
LaserIO supports multi-type transfer natively, but the receiving machine from another mod must also permit it. Open your machine's internal side configuration menu and ensure the face touching the Laser Node is set to Input/Output or Omni mode for all resource types.
How do I stop my inventory from filling up with dozens of loose cards while building?
Craft a Card Holder. When placed in your inventory and shift-right-clicked to open or toggle, it automatically stores stacks of cards, filters, and overclockers, and pulls them straight into the Laser Node GUI when you are configuring blocks.
Do Laser Nodes require power to transmit energy or items?
No, LaserIO networks are completely free to run and require zero Forge Energy to move items, fluids, or energy across laser beams.