Oritech · Mid game
Oritech 3x Ore Processing & Refinery Line
This mid-game Oritech refinery line transforms raw ores into triple the standard ingot yield plus valuable secondary metal byproducts. By chaining Pulverizers, fluid-fed Centrifuges, and high-efficiency Foundry Smelters via Item Pipes and Machine Extenders, you create a fully autonomous mineral processing backbone for your factory.
- Footprint
- 11x6x4 blocks
- Power
- ~1.5 to 3 kRF/t (check JEI for exact addon multipliers)
- Throughput
- ~1 raw ore per 2-3 seconds per parallel line
- Difficulty
- intermediate
Flow diagram
How items, fluids and energy move through the setup, left to right.
Swipe sideways to see the whole diagram
Materials
| Item | Count |
|---|---|
| Pulverizer | 2 |
| Centrifuge | 2 |
| Foundry Smelter | 2 |
| Assembler | 1 |
| Machine Core (Tier 2 / 3) | 12 |
| Machine Fluid Addon | 2 |
| Machine Speed Addon | 6 |
| Machine Efficiency Addon | 4 |
| Machine Extender | 4 |
| Item Pipe | 24 |
| Fluid Pipe | 12 |
| Energy Pipe | 20 |
| Item Filter | 2 |
| Fluid Pump | 1 |
| Chest or Storage Block | 4 |
Build it step by step
1Assemble the Machine Frames & Cores
Place down your two Pulverizers, two Centrifuges, one Assembler, and two Foundry Smelters in a linear row with at least two blocks of spacing behind them. Oritech machines are multiblock-lite structures that require Machine Cores placed directly adjacent or underneath to form; place the required Tier 2 or Tier 3 Machine Cores until each machine constructs its animated chassis.
2Install Fluid and Speed Addons
Before routing pipes, attach a Machine Fluid Addon directly to each Centrifuge (or via a Machine Extender). Without the Fluid Addon, the Centrifuge can only run dry recipes and will fail to wash Crushed Ores for maximum yield. Attach Speed and Efficiency Addons to the remaining machine faces.
3Set Up Water Supply for Washing
Build an infinite 2x2 water source near the Centrifuges and place an Oritech Fluid Pump above it. Run Fluid Pipes from the pump directly into the Fluid Addon ports on your Centrifuges, and connect an Energy Pipe to the pump so it keeps the internal tanks saturated.
4Connect the Crushing to Washing Pipeline
Place your raw ore Input Chest next to the Pulverizers and connect them using Item Pipes. Configure the pipe connection at the chest to extract (wrench the pipe node). Then run Item Pipes from the Pulverizer outputs directly into the input ports of the two Centrifuges.
5Filter Dusts and Compact Byproducts
Wet centrifugation outputs full-sized Dusts alongside Small Dust piles (such as Small Nickel or Small Platinum Dust). Place an Item Filter after the Centrifuges: route full-sized dusts straight to the Foundry Smelters, and divert all Small Dusts into the Assembler configured to pack small piles into full dusts.
6Configure the Foundry Smelters & Power Grid
Pipe the Assembler's output and the main dust line into the Foundry Smelters, then pipe the smelter outputs into your final storage chests. Finally, run Energy Pipes from your central Energy Storage along the back of every machine core and extender to power the assembly line.
How it works
In Oritech, standard furnaces give a miserable 1-to-1 conversion on raw ores. By passing raw ore through a Pulverizer first, the mechanical grinders break the chunk into Crushed Ore with a bonus yield multiplier. Instead of smelting the crushed ore directly, this setup routes it into a water-fed Centrifuge. The wet-washing recipe inside the Centrifuge multiplies the yield again while separating out trace secondary minerals in the form of Small Dusts (check JEI for specific ore byproduct tables, as Iron yields Nickel, Copper yields Gold, and Nickel yields precious Platinum).
Because Centrifuges running wet recipes generate mixed item outputs, dumping everything straight into a smelter will eventually clog the input slots with un-smeltable small dust piles. The Item Filter solves this cleanly by splitting the belt: primary dusts bypass straight to the Foundry Smelter, while Small Dusts detour through an Assembler to be compacted into standard dusts before joining the smelting queue.
Finally, using the Foundry Smelter (or regular powered Furnace depending on whether you want pure ingots or instant alloys like Electrum and Steel) finishes the process using purely RF energy instead of coal. By utilizing Machine Extenders, all power, fluid, and item connections can be tucked neatly beneath the floor while still feeding the central machine blocks.
Upgrades and scaling
- Replace the Pulverizers with a Fragment Forge once you reach late-game infrastructure; the Fragment Forge processes ores significantly faster and pushes yield multipliers even higher.
- Add Machine Capacitor Addons and extra Speed Addons through Machine Extenders to overcome the Centrifuge's relatively slow base processing cycle.
- Swap standard Item Pipes for Robotic Arms or Drone Ports when scaling horizontally across multiple factory rooms to reduce pipe lag and add visual flair.
- Dedicate one Foundry Smelter specifically to automated alloying by locking its secondary input slot to Coal Dust (for Steel) or Nickel Dust (for Invar).
Common mistakes
- Forgetting the Machine Fluid Addon on the Centrifuge: The Centrifuge will naturally run the dry recipe instead of the water-washing recipe, silently cutting your yield multiplier and losing secondary byproducts.
- Connecting pipes to unformed Machine Cores before the multiblock finishes assembling: Always place the machine block and its required Machine Cores first, wait for the visual assembly animation, and then attach pipes.
- Letting Small Dusts back up inside the Centrifuge output buffer: If the Centrifuge internal output fills up with Small Dusts because the Assembler gets jammed with mismatched 3-stacks, the entire line halts. Use a buffer chest before the Assembler.
- Under-tiering Machine Cores: Higher-tier machines and addons require higher-quality Machine Cores; check JEI and the Oritech tooltip to verify core compatibility.
FAQ
Why is my Centrifuge processing Crushed Ore without using any water?
You either forgot to attach a Machine Fluid Addon to the Centrifuge or water isn't reaching the internal tank. Without water present, the Centrifuge defaults to the dry recipe, which gives lower yields.
Can I attach pipes and addons to any block of the machine?
You can connect pipes directly to the main machine ports, its integrated Machine Cores, or attached Machine Extenders. Using Machine Extenders is the easiest way to add more faces for Speed and Efficiency Addons.
Why is my Foundry Smelter not smelting single dusts?
The Foundry Smelter is designed primarily for 2-input alloying recipes unless configured properly or fed compatible combinations. If you only want simple 1-to-1 dust-to-ingot smelting without alloying, use the standard powered Furnace from Oritech or lock the Foundry mode.