OpenComputers · Early game
Automated Tinkers' Smeltery & Alloying Foundry
This setup integrates an OpenComputers Tier 1 system directly with a Tinkers' Construct Smeltery to automate metal melting, fluid sorting, and ingot pouring. By utilizing OpenComputers Adapter drivers and a Redstone I/O block, it reads the internal molten fluids, prevents accidental alloying by holding conflict ores, and pulses the Seared Faucets automatically. It is an ideal early-game project to eliminate manual smeltery babysitting and accidental bronze or brass creation.
- Footprint
- 7x5x4 blocks
- Power
- Minimal (check JEI for exact OC config, easily run by 1 coal generator)
- Throughput
- ~1 ingot every 6 seconds per faucet
- Difficulty
- intermediate
Flow diagram
How items, fluids and energy move through the setup, left to right.
Swipe sideways to see the whole diagram
Materials
| Item | Count |
|---|---|
| Smeltery Controller | 1 |
| Seared Tank | 1 |
| Seared Bricks | 32 |
| Seared Drain | 2 |
| Seared Faucet | 2 |
| Casting Table | 1 |
| Casting Basin | 1 |
| Ingot Cast | 1 |
| Computer Case (Tier 1) | 1 |
| Screen (Tier 1) | 1 |
| Keyboard | 1 |
| Adapter | 1 |
| Transposer | 1 |
| Redstone I/O | 1 |
| Cable (OpenComputers) | 8 |
| CPU (Tier 1) | 1 |
| Memory (Tier 1.5) | 2 |
| Graphics Card (Tier 1) | 1 |
| Hard Disk Drive (Tier 1) | 1 |
| EEPROM (Lua BIOS) | 1 |
| OpenOS Floppy Disk | 1 |
| Disk Drive | 1 |
| Hopper | 2 |
| Chest | 2 |
| Redstone Dust | 4 |
Build it step by step
1Construct the Base Smeltery
Build a standard 3x3 internal volume Tinkers' Construct Smeltery using Seared Bricks. Place the Smeltery Controller, Seared Tank, and two Seared Drains on the front walls at the bottom layer. Fill the Seared Tank with lava to make the multi-block structure valid.
2Set Up the Casting Outputs
Mount a Seared Faucet onto each of the two Seared Drains. Place a Casting Table with an Ingot Cast under one faucet, and a Casting Basin under the second faucet. Place vanilla Hoppers underneath both the Table and Basin, pointing directly into your Output Chest.
3Install the Input Logistics
Place the OpenComputers Transposer directly adjacent to or on top of the Smeltery Controller. Place your Input Chest directly touching the Transposer. This allows the computer to precisely inspect and move items one by one into the Smeltery.
4Connect the OpenComputers Hardware
Place the Adapter block so it directly touches the Smeltery Controller (or a Seared Drain). Place the Redstone I/O block within wiring reach of the Seared Faucets and run vanilla Redstone Dust from the Redstone I/O to both faucets. Connect the Adapter, Transposer, and Redstone I/O back to your Computer Case using OpenComputers Cables.
5Assemble and Boot the Computer
Place the Screen and Keyboard attached to the Computer Case, along with a Disk Drive and a basic power source if your modpack requires energy for OpenComputers. Insert the CPU, Memory, Graphics Card, Hard Disk, and Lua BIOS EEPROM into the case, put the OpenOS Floppy into the Disk Drive, and turn on the computer. Run the install command to load OpenOS onto the Hard Disk.
6Write the Control Script
Create a Lua script that wraps the Smeltery Controller component via the Adapter and the Transposer component. Program a loop that checks the currently melted fluids inside the smeltery, moves safe non-alloying items from the Input Chest via the Transposer, and triggers the Redstone I/O to pulse the faucets whenever at least 144mB of liquid metal is ready.
How it works
The core of this setup relies on the OpenComputers Adapter interfacing with the Tinkers' Construct Smeltery Controller. When touching the controller or a drain, the Adapter exposes methods to query the exact types and millibucket amounts of molten fluids currently residing inside the smeltery. Before any new raw ore is inserted from the Input Chest, the Lua script reads the item's name via the Transposer and cross-references it against a user-defined blacklist of alloying combinations (such as Copper and Tin, or Iron and Nickel).
If the smeltery is currently empty or only contains compatible metals, the Transposer transfers the ore into the Smeltery Controller to begin melting. Meanwhile, the script monitors the bottom-most fluid in the smeltery tank. Once the fluid volume reaches a clean multiple of an ingot (typically 144mB, though you should check JEI for your specific modpack settings) or a full block (1296mB), the computer tells the Redstone I/O block to emit a brief redstone pulse to the appropriate Seared Faucet. The faucet pours the liquid into the Casting Table or Basin, and the vanilla Hopper below immediately pulls the cooled ingot into the Output Chest, clearing the table for the next pour.
Upgrades and scaling
- Replace the vanilla Redstone I/O and Seared Faucets with fluid pipes from another early-game tech mod (like Thermal Dynamics Fluiducts) toggled by the computer for much faster pouring speeds.
- Add a Tier 2 Screen and Tier 2 Graphics Card to display a color-coded GUI showing current molten metal levels, fuel remaining, and queued ores.
- Expand the smeltery vertically by adding more rings of Seared Bricks to increase parallel melting capacity without changing the footprint or code.
Common mistakes
- Placing the Adapter against standard Seared Bricks instead of the Smeltery Controller or a Seared Drain; standard bricks do not expose the component methods to OpenComputers.
- Using a continuous redstone signal instead of a short pulse from the Redstone I/O to the Seared Faucet; faucets require a rising edge pulse to trigger each individual pour.
- Forgetting to put a Hopper underneath the Casting Table, which causes the table to remain full after the first ingot cools and halts all subsequent pouring operations.
- Allowing the smeltery to hold leftover fractional amounts of metal (like 72mB from melted gear or nuggets) without a fallback cast, which clogs the bottomfluid slot and stops ingots from pouring.
FAQ
Why is my Adapter not detecting the Smeltery?
Ensure the Adapter is physically touching the Smeltery Controller or a Seared Drain, and verify that your modpack includes OpenComputers drivers for Tinkers' Construct (often provided natively or via an addon like Computronics or Plethora depending on the version).
How do I change which fluid pours next if multiple metals are inside?
While you cannot click the GUI remotely with a Tier 1 setup, the script prevents multiple incompatible fluids from entering at the same time, ensuring one metal drains completely before the next ore type is inserted by the Transposer.
Can I run this setup without any RF or FE power?
If you change the OpenComputers config file to ignore power requirements it works for free, otherwise you must attach a basic early-game RF/FE generator or an OpenComputers Generator upgrading with coal to a Cable.