Storage Drawers · Early game
Automated Quarry Bulk Ore Wall & Trash Voiding Setup
This setup provides an automated, lag-free bulk sorting and trash voiding system specifically designed to handle the chaotic output of early-game mining machines and quarries. By utilizing a centralized Drawer Controller connected to a locked wall of upgraded drawers, it instantly separates high-volume junk blocks from valuable ores and ingots. Building this prevents chest monster overflow and ensures your quarry never backs up or spills items into the world.
- Footprint
- 7x2x5 blocks
- Power
- 0 FE/t (Passive Redstone/Hopper Logic)
- Throughput
- ~2.5 items/sec (Vanilla Hopper speed, scalable with pipes)
- Difficulty
- beginner
Flow diagram
How items, fluids and energy move through the setup, left to right.
Swipe sideways to see the whole diagram
Materials
| Item | Count |
|---|---|
| Drawer Controller | 1 |
| Oak Drawers 1x1 | 8 |
| Oak Drawers 2x2 | 12 |
| Compacting Drawers | 4 |
| Oak Trim | 4 |
| Drawer Key | 1 |
| Quantify Key | 1 |
| Void Upgrade | 12 |
| Obsidian Storage Upgrade | 8 |
| Iron Storage Upgrade | 16 |
| Upgrade Template | 36 |
| Hopper | 2 |
| Chest | 4 |
Build it step by step
1Place the Central Drawer Controller
Start by placing your Drawer Controller in the bottom-center of your planned 7-block-wide wall, elevated one block off the floor. Make sure the front face is accessible so you can still manually double-right-click it to dump your personal mining inventory when needed.
2Construct the Bulk Trash & Ore Wall
Flank the Drawer Controller with Oak Trim on the bottom row to bridge the connection, then build a 7x4 grid of drawers directly touching each other and the controller. Place the 8 Oak Drawers 1x1 on the left side for extreme-volume junk blocks, the 4 Compacting Drawers in the center above the controller, and the 12 Oak Drawers 2x2 on the right side for specific raw ores and gems.
3Lock the Network with the Drawer Key
Hold the Drawer Key in your main hand and right-click the front face of the Drawer Controller once. This instantly locks every single connected drawer in the contiguous wall, meaning empty slots will no longer accept random items and occupied slots will remember their assigned item even when completely emptied. Do the same with the Quantify Key so you can visually monitor exact item counts.
4Seed Items into Specific Slots
Manually insert at least one of every expected quarry output into its designated drawer slot. Assign Cobblestone, Cobbled Deepslate, Dirt, Gravel, Diorite, Andesite, Granite, and Tuff to the 1x1 drawers. Put Redstone, Lapis, and processed metals into the Compacting Drawers, and fill the 2x2 drawers with Raw Iron, Raw Copper, Raw Gold, Coal, and Diamonds.
5Install Storage and Void Upgrades
Shift-right-click the Oak Drawers 1x1 with Obsidian Storage Upgrades and Void Upgrades. Install Iron Storage Upgrades into the 2x2 and Compacting Drawers, adding extra Void Upgrades to high-yield ore drawers like Coal, Redstone, or Copper so they never bottleneck the system once full.
6Set Up the Priority Hopper Overflow Chain
Place the Primary Input Hopper directly behind the Drawer Controller, pointing straight into its back face, and place your Quarry Input Chest on top of this hopper. Next, place the Overflow Hopper directly underneath the Primary Input Hopper, pointing sideways into an Overflow Double Chest. Because every drawer in the network is locked, any unseeded or weird items that cannot enter the Drawer Controller will naturally get pulled downward into the Overflow Double Chest.
How it works
The core strength of this design lies in how the Drawer Controller scans connected blocks and enforces item locking. When the Drawer Controller receives an item from the Primary Input Hopper, it checks every contiguous drawer and trim block within its range (check JEI or mod configs for exact radius, usually 12 blocks) for a matching slot. Because we locked the entire wall using the Drawer Key, the controller is strictly forbidden from putting unassigned items into blank slots.
We leverage vanilla Minecraft hopper priority mechanics to create a zero-power sorting and overflow filter. When an item enters the Primary Input Hopper, the hopper tries to push it sideways into the Drawer Controller while simultaneously being pulled from below by the Overflow Hopper. If you want strict priority where the Drawer Controller always wins before the bottom hopper pulls, you can place your input chest to the side, run a horizontal hopper chain over the top of the Drawer Controller, and place the overflow chest at the very end of the hopper line.
Finally, the Void Upgrades act as an automatic pressure-relief valve for your quarry. Early-game quarries yield massive quantities of Cobblestone, Dirt, and Deepslate that quickly overwhelm standard storage. When an upgraded 1x1 drawer reaches its maximum stack limit, it continues accepting matching items from the Drawer Controller and silently deletes the excess, keeping the input hopper completely clear for valuable Diamonds and Raw Ores.
Upgrades and scaling
- Replace the Obsidian and Iron Storage Upgrades with Gold, Diamond, or Emerald Storage Upgrades as your resource production scales up to multiply drawer capacity dramatically.
- Swap out the vanilla hoppers for high-speed modded item pipes (such as Pipez, Mekansim Logistical Transporters, or Thermal ducts) using nearest-first priority routing to handle blazing-fast mid-game quarries.
- Attach a Controller Slave to the back corners of the drawer wall via Oak Trim to add extra input/output extraction faces for automated smelting setups without breaking the contiguous network.
- Install Redstone Upgrades or Min Redstone Upgrades on critical resource drawers to emit a comparator-style redstone signal that automatically shuts off your quarry when storage is completely full.
Common mistakes
- Forgetting to lock the Drawer Controller with a Drawer Key before hooking up the quarry, which results in random junk like Mob Drops or Flint permanently claiming your high-capacity 1x1 drawers.
- Leaving an air gap between drawers without bridging it with Oak Trim; all blocks must touch face-to-face (not diagonally) within the controller's radius to stay connected to the network.
- Using 2x2 drawers for high-volume blocks like Cobblestone instead of 1x1 drawers; 2x2 drawers split the total base stack capacity across four slots, giving each slot one-fourth the storage of a 1x1 drawer.
- Placing Void Upgrades on drawers without first locking and seeding them, which can accidentally void valuable unseeded items if the drawer becomes unlocked and fills up.
FAQ
Why is my Drawer Controller rejecting items even though I have empty drawers on the wall?
When a drawer is locked with a Drawer Key and left completely blank, it refuses all items. You must manually right-click at least one item into the locked slot to assign its filter.
How do I extract ores from the wall to send them to my furnaces automatically?
You cannot easily filter extraction from the Drawer Controller itself with basic hoppers. Instead, place a hopper directly underneath the specific Raw Ore drawer you want to empty, or use a filtered item pipe attached to the Drawer Controller or a Controller Slave.
Can I mix different wood types of drawers and trim on the same controller wall?
Yes, Storage Drawers allows any wood variant, Framed Drawers, and Compacting Drawers to connect seamlessly through the same Drawer Controller network.