Extreme Reactors · Addon guide · Intermediate
Extreme Reactors Uranium Compat & ZeroCore Configuration Guide
In multi-mod environments, dealing with separate Yellorium and Uranium ores cluttering your world generation and storage systems is a common headache. This guide explains how to unify your nuclear fuel supply to burn standard modded Uranium in your Extreme Reactors, and how to use built-in ZeroCore and Extreme Reactors commands to dynamically tune fuel properties and turbine coils in-game.
What you need
- Extreme Reactors and its required dependency library, ZeroCore
- Patchouli (optional, for the in-game book) and JEI for checking reactant tags
- A completed Basic or Reinforced Reactor multiblock with a Solid Access Port or Fuel Injection Port
- Operator permission (OP Level 2 or higher) to run configuration commands
- Another tech mod providing standard Uranium Ingots (or a compatibility addon / datapack)
Step by step
1Verify Current Uranium and Yellorium Tags
Open your inventory, search for Yellorium Ingot and Uranium Ingot in JEI, and press advanced tooltips (F3 + H) to view their item tags. Look for the shared Forge tag `forge:ingots/uranium` or `forge:ingots/yellorium`. In recent versions of Extreme Reactors, Yellorium often shares the uranium tag out of the box, or can be bridged using a compatibility addon or simple datapack.
Tip: If your modpack does not automatically unify them, check the Extreme Reactors common configuration file for reactant registration settings or install a dedicated Uranium Compat datapack.
2Test Uranium Insertion in the Solid Access Port
Walk up to your assembled Reactor multiblock and right-click the Reactor Solid Access Port (set to Inlet mode). Place a standard Uranium Ingot from another mod into the input slot. If the item is registered in the ReactantsRegistry, it will immediately convert into internal fuel mass displayed in the Reactor Controller GUI.
Tip: You can also convert solid Uranium into liquid fuel inside the Fluidizer multiblock using a Fluidizer Solid Injector.
3Disable Duplicate Ore Generation
Once you confirm your reactor accepts standard Uranium Ingots, you no longer need both Yellorite Ore and Uranium Ore generating in new chunks. Exit to your instance configuration folder and open the Extreme Reactors worldgen config file (or use a worldgen management datapack in newer Minecraft versions). Disable Yellorite Ore generation so your world only spawns a single unified Uranium ore type.
Tip: Never disable Yellorite generation before verifying that your other mod's Uranium is accepted by both the Reactor Solid Access Port and the Fluidizer.
4Access the In-Game /er Command Suite
Ensure you have at least OP Level 2 permissions on your server or have cheats enabled in single-player. Open the chat console and type `/er` followed by a space to view the auto-complete command tree provided by Extreme Reactors and ZeroCore. This command suite allows live inspection and tuning of registered reactants, fuels, and turbine blocks without restarting the game.
5Tune Fuel Reactant Properties Live
Use the `/er` fuel subcommands to inspect or modify how your unified Uranium (or advanced fuels like Blutonium and Verderium) behaves inside the core. You can adjust parameters such as moderation factor, absorption, hardness, and fission events per fuel unit. When you execute the command, the Reactor Controller recalculates heat and Forge Energy (FE/t) output immediately.
Tip: If you add a custom fuel via the API without specifying properties, it automatically inherits the default Yellorium values.
6Balance Custom Turbine Coils with /er coils
If you are running a Reinforced Turbine alongside an actively cooled reactor, you can balance coil blocks using the `/er coils` command. Test how built-in endgame coils like Ludicrite, Ridiculite, and Inanite perform, or target any modded metal block registered as a turbine coil. Adjust the efficiency and energy extraction multipliers until the FE/t output matches your progression goals.
Tip: A full high-tier coil in a max-size Reinforced Turbine can easily reach tens of thousands of FE/t, so make small incremental adjustments when tuning.
7Verify Waste Reprocessing Compatibility
Check your Reactor Solid Access Port (set to Outlet mode) after burning your unified Uranium fuel. Standard Uranium/Yellorium fuel burns into Cyanite Ingots (or liquid Cyanite via a Fuel Injection Port). Take that Cyanite to a 3x3x7 Reprocessor multiblock, feed it into the top Reprocessor Waste Injector along with Water in the Reprocessor Fluid Injector, and confirm it properly outputs Blutonium.
Tip: Check JEI for exact Reprocessor recipes, as fluid and power requirements can vary by modpack.
How it works
Extreme Reactors does not hardcode a single item ID for its nuclear fuel. Instead, it relies on an internal system called the ReactantsRegistry and FuelProperties managed through ZeroCore. In this system, physical items (like Yellorium Ingots, Uranium Ingots, or Blutonium Ingots) and fluids are mapped to abstract internal 'Reactants'. When you insert an item into a Reactor Solid Access Port, the port checks if the item's ID or Forge tag is mapped to a registered Fuel Reactant, and if so, adds a specific amount of reactant mass to the Fuel Rods.
Because the physical item is destroyed upon insertion and converted into internal reactant data, any modded Uranium Ingot mapped to the Yellorium reactant behaves identically inside the core. It will generate the exact same radiation, heat, and Forge Energy, and when depleted, it will produce the exact same waste reactant (Cyanite, or Magentite when burning Blutonium). The `/er` commands hook directly into these runtime registries, letting players and pack authors tweak radiation hardness, fuel burn rates, and turbine coil induction values on the fly to prototype balance changes before committing them to configuration files.
Common mistakes
- Disabling Yellorite Ore generation before verifying tag unification, which leaves you unable to fuel your reactor if the other mod's Uranium uses a non-standard item tag.
- Trying to pump liquid Uranium or liquid Yellorium into a Reactor Solid Access Port; fluid fuels require a dedicated Reactor Fuel Injection Port.
- Forgetting to check Fluidizer recipes in JEI after unifying Uranium, as some custom solid-to-liquid mixing recipes (like creating Verderium) may still specifically request a certain tag or item if configured improperly.
- Tuning `/er` fuel or coil values in a live testing world and assuming they permanently rewrite static datapacks; always back up your tuned values into your server scripts or config files.
FAQ
What happens if I feed standard Uranium in, what waste comes out?
Because standard Uranium is mapped to the Yellorium fuel reactant, the reactor will output standard Cyanite Ingots (or liquid Cyanite) at the Outlet port.
Why do the /er commands say I do not have permission?
The `/er` tuning commands require Operator Level 2 or higher. In single-player, pause the game, click 'Open to LAN', and set 'Allow Cheats' to ON.
Can I mix Uranium with other fuels to make a stronger reactant?
Yes! By building the Fluidizer multiblock with two Fluidizer Solid Injectors (or Fluid Injectors), you can melt and combine two different fuels into high-tier liquid fuel like Verderium. Check JEI for the exact combinations.
What are the best turbine coils to tune or use in modern Extreme Reactors?
Beyond standard modded metals, the mod includes three dedicated endgame coil materials: Ludicrite, Ridiculite, and Inanite, in ascending order of power extraction.
By leveraging the ReactantsRegistry for Uranium tag unification and using the `/er` command suite to tune fuel properties and turbine coils, you can seamlessly integrate Extreme Reactors into any modded tech progression.