Extreme Reactors · Early game
Compact 3x3x3 Starter Passive Reactor
The Compact 3x3x3 Starter Passive Reactor is the quickest gateway to stable Forge Energy (FE) or Redstone Flux (RF) in the early game. Relying entirely on passive air cooling, this minimalist multiblock eliminates the need for expensive coolant liquids while delivering far more power than basic coal generators. It requires only basic iron, coal, redstone, and a handful of Yellorium to construct and run.
- Footprint
- 3x3x3 blocks
- Power
- ~250 to 500 FE/t (check JEI or mod config for exact modpack multipliers)
- Throughput
- Very low fuel usage (~0.02 mB/t of Yellorium)
- Difficulty
- beginner
Flow diagram
How items, fluids and energy move through the setup, left to right.
Swipe sideways to see the whole diagram
Materials
| Item | Count |
|---|---|
| Reactor Casing | 21 |
| Reactor Controller | 1 |
| Reactor Control Rod | 1 |
| Reactor Fuel Rod | 1 |
| Reactor Access Port | 2 |
| Reactor Active Power Tap | 1 |
| Hopper | 2 |
| Chest | 2 |
| Yellorium Ingot | 16 |
Build it step by step
1Smelt Graphite and Craft Components
Begin by smelting regular Coal or Charcoal in a Furnace to produce Graphite Bars. Combine these with Iron Ingots and Yellorium Ingots at a crafting table to make all your Reactor Casings and specialized ports. Check JEI for the exact recipes, as you will need Basic variants of the components if playing on newer mod versions.
2Lay the 3x3 Base Layer
Place a solid 3x3 square of 9 Reactor Casings flat on the ground. Every outer edge, corner, and the center block of this bottom layer must be made of standard Reactor Casings.
3Place the Central Fuel Rod
Stand on the base and place your single Reactor Fuel Rod directly on top of the center Reactor Casing. This single block acts as the core of your 3x3x3 multiblock.
4Build the Middle Layer Walls
Place 4 Reactor Casings on the four corners of the middle layer. In the four remaining side positions, install 1 Reactor Controller, 1 Reactor Active Power Tap, and 2 Reactor Access Ports.
5Cap the Roof Layer
For the top 3x3 layer, build the outer ring using 8 Reactor Casings. Place the Reactor Control Rod in the exact center block directly above the Reactor Fuel Rod. Once placed, the multiblock texture should connect and form a complete structure.
6Configure the Access Ports
Right-click one Reactor Access Port and confirm it is set to Inlet Mode (typically indicated by a green inward arrow). Right-click the second Reactor Access Port and toggle its button to Outlet Mode (typically a red outward arrow) so it exclusively ejects waste.
7Attach Hoppers and Fuel Up
Attach a Hopper leading into the Inlet Port with a Chest on top, and place a Chest underneath a Hopper pulling from the Outlet Port. Drop your Yellorium Ingots into the input Chest, then open the Reactor Controller GUI and click the Activate button to begin generating power.
How it works
Extreme Reactors multiblocks generate heat through nuclear fission inside the Reactor Fuel Rod. Because a 3x3x3 structure has no extra interior space surrounding the central rod, it uses the outer casing shell itself to passively dissipate heat into the environment. This thermal heat is automatically converted into FE or RF inside the internal energy buffer, which is then pushed into your base's energy cables via the Reactor Active Power Tap.
As the reactor operates, it slowly consumes Yellorium from the internal fuel tank and converts it into depleted Cyanite waste. Once a full 1000 mB of waste accumulates, the reactor materializes a Cyanite Ingot and pushes it to the Outlet Access Port. If the internal energy buffer reaches 100% capacity because your base is not using enough power, you can insert the Reactor Control Rod via the GUI to slow down the fission reaction and conserve fuel.
Upgrades and scaling
- Expand the outer shell to a 5x5x5 footprint and surround the central fuel rod tower with internal coolants like Destabilized Redstone, Liquid Ender, or Diamond Blocks to massively multiply power output and fuel efficiency.
- Save every Cyanite Ingot produced in the waste chest; you will need them later to craft a Cyanite Reprocessor to create Blutonium and construct high-tier actively cooled turbines.
- Install two Reactor Redstone Ports (or RedNet Ports) to automate power management, setting one to read the internal energy buffer percentage and the other to adjust Control Rod insertion so it never wastes Yellorium when your battery is full.
Common mistakes
- Using decorative components on the frame: The 12 outer edges and 8 corners of the 3x3x3 cube must only consist of solid Reactor Casings. Placing ports, taps, or glass on any edge will prevent the multiblock from forming.
- Forgetting to set an Outlet Port: If both Access Ports are left on Inlet mode, Cyanite waste will build up inside the core and completely halt fuel consumption and power generation once the waste tank fills.
- Leaving the reactor running at 0% control rod insertion with an empty base: Unlike some generators, an Extreme Reactor will continue burning Yellorium at full heat even when its internal power buffer is 100% full.
FAQ
Can an Extreme Reactor overheat and explode?
No. Extreme Reactors are completely safe and will never melt down or cause terrain damage. Running at extreme temperatures simply lowers your fuel efficiency and consumes Yellorium much faster.
Can I use Uranium instead of Yellorium?
Yes, in almost all modpacks, Uranium Ingots share the same forge ore dictionary tag as Yellorium Ingots and can be fed directly into the Inlet Access Port.
Why isn't my reactor forming when I place the final block?
Right-click any block of the reactor with an empty hand. The mod will display an error message in your chat box telling you the exact coordinates of the invalid or missing block.