Forestry · Late game
Forestry Multiblock Alveary Rapid Mutation & Production Setup
The Forestry Multiblock Alveary Rapid Mutation & Production Setup is a late-game apiculture engine designed to bypass the slow RNG of standard Bee Houses and Apiaries. By integrating Alveary Mutators, Frame Housings, and climate control modules into a single 3x3x3 structure, this system guarantees 100% mutation rates or massively boosts specialty Honeycomb production per bee tick. You should build this to rapidly unlock high-tier bee species and automate the extraction of valuable resources like Royal Jelly, Pollen Clusters, and mineral combs.
- Footprint
- 7x5x5 blocks
- Power
- Moderate RF/FE per tick (check JEI for exact Centrifuge and Heater draw)
- Throughput
- Multiple Combs per bee cycle; 1-generation guaranteed mutations
- Difficulty
- advanced
Flow diagram
How items, fluids and energy move through the setup, left to right.
Swipe sideways to see the whole diagram
Materials
| Item | Count |
|---|---|
| Alveary | 21 |
| Alveary Frame Housing | 2 |
| Alveary Mutator | 2 |
| Alveary Heater | 1 |
| Alveary Fan | 1 |
| Oak Wood Slab | 9 |
| Centrifuge | 1 |
| Chest | 3 |
| Hopper | 6 |
| Proven Frame | 2 |
| Chocolate Frame | 2 |
Build it step by step
1Prepare the Base Layer
Select a flat area in a neutral biome (like Plains or Forest) to make climate adjustments easier. Place the bottom 3x3 layer of the multiblock using 7 standard Alveary blocks, 1 Alveary Heater, and 1 Alveary Fan on the outer bottom edges. Keeping climate control blocks on the bottom layer allows easy cable routing from underneath.
2Assemble the Functional Middle Layer
On the second 3x3 layer, place standard Alveary blocks in the center and corners, leaving the four middle side positions open for functional modules. Install 2 Alveary Mutators and 2 Alveary Frame Housings into these side slots so their inventories are easily accessible from the outside.
3Cap the Alveary Roof
Build the third 3x3 layer entirely out of standard Alveary blocks to complete the 27-block solid cube. Place 9 Wooden Slabs directly on top of the third layer; the multiblock will visually merge into a single large beehive structure if assembled correctly.
4Connect Bee Loop Logistics
Attach your item extraction and sorting system (using Forestry Genetic Filters or standard Hoppers) to any standard Alveary block. Configure the filter to route the output Princess and one matching Drone directly back into the Alveary input slots, while sending excess Drones and Honeycombs down a separate output line.
5Automate Frames and Mutagens
Place Hoppers or item pipes feeding directly into the Alveary Frame Housings and Alveary Mutators. Load the Mutator input Chest with mutagenic catalysts like Soul Sand, Ender Pearls, or Uranium Ore (check JEI for exact multiplier values), and supply the Frame Housings with Chocolate Frames for fast mutation or Proven Frames for comb production.
6Wire Power and Processing
Place the Centrifuge adjacent to your comb output line and connect it to a final storage Chest. Run energy cables from your FE/RF power source to the Centrifuge, Alveary Heater, and Alveary Fan, toggling the climate blocks only when breeding species from extreme biomes like the Nether or Icy regions.
How it works
Unlike standard Apiaries, the Alveary is a 3x3x3 multiblock where every constituent block shares the internal inventory of the central queen, except for specialized sub-blocks that hold their own modifier items. When a Princess and Drone are inserted, they merge into a Queen. Before the Queen completes her lifecycle, the Alveary checks any attached Alveary Mutators and Alveary Frame Housings. Consuming a high-tier mutagen item inside the Mutator block multiplies the base mutation chance of the pairing, easily pushing even 2% late-game mutations up to 100%.
When switching from breeding mode to resource production mode, you simply stop feeding the Mutators and swap the Chocolate Frames in the Frame Housings for Proven Frames or Impregnated Frames. Each Frame Housing doubles the bee's production speed modifier, allowing the Queen to generate specialty combs every few seconds. Furthermore, specialty items like Royal Jelly (from Imperial Bees) and Pollen Clusters (from Industrious Bees) can only be produced when the bees are housed in an Alveary that meets their exact base temperature and humidity requirements.
The automated sorting loop ensures continuous operation without manual supervision. As soon as a Queen dies, the offspring Princess, Drones, and produced Honeycombs are pulled out into the Genetic Filter. The Princess and a single Drone are immediately cycled back into the Alveary to start the next generation, while Honeycombs are routed into the powered Centrifuge to be spun down into Honey Drops, Beeswax, and valuable late-game drops.
Upgrades and scaling
- Install an Alveary Rain Shield block into the base layer to allow non-flyer bees to continue working uninterrupted during rainstorms.
- Add an Alveary Lighting block to remove the need for the nocturnal trait, enabling 24/7 breeding and comb production through the night.
- Insert an Alveary Hygroregulator fed with Water or Lava pipes to shift humidity levels alongside the Heater and Fan for total biome emulation.
- Upgrade the single Centrifuge to a multi-Centrifuge array enhanced with Upgraded Circuit Boards (loaded with Bronze or Gold Electron Tubes) to prevent comb backlogs during high-speed production.
- Swap out basic frames for Oblivion Frames (if auxiliary bee addons are installed) to reduce Queen lifespan to a single tick for instant genetic mutations.
Common mistakes
- Placing functional blocks like Frame Housings or Mutators in the top 3x3 layer of the Alveary, which prevents the multiblock from forming properly.
- Using more than two high-tier mutagens (such as Uranium) at once, which can push the mutation multiplier too high and cause genetic decay, turning your Princess into a Swarmer bee with a finite lifespan.
- Stacking four or more Frame Housings filled with production frames without genetic reinforcement, which causes genetic fatigue and likewise degrades your purebred Queen into a temporary Swarmer.
- Forgetting to place the 9 Wooden Slabs on top of the 3x3x3 structure; without the slab roof, the blocks remain inactive and will not accept bees.
- Piping frames or mutagens into a standard Alveary block instead of directly into the side of the Alveary Frame Housing or Alveary Mutator block.
FAQ
Why is my Alveary not producing Royal Jelly or Pollen Clusters?
Specialty products require the Alveary's internal climate to match the bee species' preferred temperature and humidity without relying on acclimatized tolerance traits. Use the Alveary Heater, Fan, or Hygroregulator to hit the exact Normal/Normal climate required by Imperial and Industrious bees.
How do I switch between rapid mutation and honeycomb production?
For rapid mutation, insert Chocolate Frames into the Frame Housings (to shorten Queen lifespan) and load mutagens into the Alveary Mutators. For comb production, leave the Mutators empty and load Proven or Impregnated Frames into the Frame Housings.
Can two Alvearies share the same wall or functional blocks?
No, Alvearies cannot share blocks and must have at least a 1-block air gap between them, otherwise both multiblocks will fail to form.