Applied Energistics 2 · Early game
High-Speed Processor & Crystal Growth Factory
This setup automates the production of Logic, Calculation, and Engineering Processors alongside pure crystal growth using AE2 Stuff expansion machines. By replacing tedious in-world water pools and sided vanilla Inscribers with Crystal Growth Chambers and Advanced Inscribers, you eliminate early-game bottlenecks. It operates cleanly off a simple hopper and chest chain before your main ME network is even online.
- Footprint
- 7x3x4 blocks
- Power
- Moderate AE/t or FE/t (check JEI for your pack)
- Throughput
- ~1 processor every few seconds with Acceleration Cards
- Difficulty
- beginner
Flow diagram
How items, fluids and energy move through the setup, left to right.
Swipe sideways to see the whole diagram
Materials
| Item | Count |
|---|---|
| Advanced Inscriber | 5 |
| Crystal Growth Chamber | 1 |
| Energy Acceptor | 1 |
| Fluix ME Glass Cable | 8 |
| Inscriber Silicon Press | 1 |
| Inscriber Logic Press | 1 |
| Inscriber Calculation Press | 1 |
| Inscriber Engineering Press | 1 |
| Acceleration Card | 18 |
| Hopper | 10 |
| Chest | 4 |
Build it step by step
1Lay the Power Spine
Place your Energy Acceptor at one end of the build area and connect it to your early-game forge energy generator. Run a line of 6 Fluix ME Glass Cables horizontally one block above the ground to distribute AE power.
2Install the Crystal Growth Chamber
Place the Crystal Growth Chamber directly against the first Fluix Cable. Place an Input Chest on top of it with a Hopper pointing down so Certus Quartz Seeds and Fluix Seeds can drop straight in without needing water.
3Set Up Printing Inscribers
Place four Advanced Inscribers in a row next to the Crystal Growth Chamber, all touching the Fluix Cable line. Insert the Silicon Press into the first, Logic Press into the second, Calculation Press into the third, and Engineering Press into the fourth.
4Lock and Upgrade the Inscribers
Open each Advanced Inscriber interface and toggle the slot locks if available so raw materials only enter valid slots. Add up to 3 Acceleration Cards into each Advanced Inscriber and the Crystal Growth Chamber to maximize processing speed.
5Route Printed Components
Place Hoppers underneath the four printing Advanced Inscribers feeding into a central Buffer Chest. Unlike standard AE2 Inscribers, Advanced Inscribers are not strictly side-locked and can accept and output items from any face.
6Connect the Final Assembly Inscriber
Place the fifth Advanced Inscriber below or beside the Buffer Chest, connected via Hoppers. Feed Redstone directly into this machine alongside the Printed Silicon and Printed Circuits coming from the Buffer Chest.
7Attach the Output Chest
Place one final Hopper beneath the assembly Advanced Inscriber leading into your Output Chest. Finished Logic, Calculation, and Engineering Processors will collect here automatically.
How it works
Standard Applied Energistics 2 Inscribers are notoriously frustrating in the early game because they require items to be inserted from very specific faces (top, bottom, and side) and only hold a single item per slot rather than a full stack. By upgrading immediately to AE2 Stuff's Advanced Inscribers, the sidedness restriction is removed and internal buffers accept full stacks of 64 items, allowing simple vanilla Hoppers to feed them cleanly.
Similarly, the Crystal Growth Chamber encloses the crystal purification mechanic inside a single powered block. Instead of dropping Certus Quartz Seeds into a water puddle surrounded by powered Crystal Growth Accelerators that constantly drain power, the chamber only consumes energy while actively growing seeds and outputs Pure Certus Quartz Crystals directly into adjacent inventories.
The production line splits into two stages: stamping and assembly. The first bank of four Advanced Inscribers stamps raw Silicon, Gold Ingots, Pure Certus Quartz, and Diamonds into their printed circuit forms. These intermediate parts funnel into a buffer chest and then drop into the fifth Advanced Inscriber with Redstone, completing the finished processors.
Upgrades and scaling
- Replace the vanilla Hoppers and Chests with ME Import Buses and ME Export Buses once your ME Controller and storage drives are online.
- Attach ME Interfaces with Processing Patterns to each Advanced Inscriber for on-demand autocrafting.
- Fill all remaining upgrade slots in the Crystal Growth Chamber and Advanced Inscribers with maximum Acceleration Cards.
Common mistakes
- Using regular AE2 Inscribers instead of Advanced Inscribers, which will jam immediately when fed from a single Hopper.
- Forgetting to supply power via an Energy Acceptor or ME Controller; Advanced Inscribers require AE network power, not direct RF/FE cables.
- Mixing different types of Printed Circuits in the final assembly Inscriber without matching counts of Printed Silicon and Redstone, causing the input slots to clog.
- Leaving out Acceleration Cards, which makes base machine operation extremely slow.
FAQ
Do I need water inside or around the Crystal Growth Chamber?
No, the Crystal Growth Chamber operates completely dry and only requires AE power to grow seeds.
Why won't my power cables connect directly to the Advanced Inscribers?
AE2 Stuff machines require Applied Energistics power (AE), so you must pass your forge energy through an Energy Acceptor and use Fluix Cables.
Can I put more than one press into the same Advanced Inscriber?
No, each dedicated press should have its own Advanced Inscriber so you can run whole stacks of materials without manually swapping plates.