Ad Astra · Automation · Intermediate
Automating Fluids & Oxygen: Water Pumps, Fluid Pipes, and Wrench Mechanics
Manually hauling buckets of water and fuel to keep your space program running gets tedious fast. In this guide, you will learn how to master Ad Astra's Fluid Pipes and Wrench mechanics to completely automate infinite water pumping, continuous oxygen generation, and hands-free rocket fueling. Setting up these fluid networks early will save you hours of manual labor and keep your off-world bases breathing easily.
What you need
- Water Pump
- Oxygen Loader (or Oxygen Distributor for base life support)
- Fuel Refinery
- Ostrum Fluid Pipes (or Desh Fluid Pipes for basic setups)
- Wrench (Ad Astra variant)
- Power generation and Cables (e.g., Coal Generator, Solar Panel, and Steel Cables)
- Water Buckets (at least two to make an infinite water source)
- Launch Pad and a Rocket
- Astrodux (the in-game guidebook) or JEI for checking exact crafting recipes
Step by step
1Build an Infinite Water Source and Place the Pump
Dig a 3x1 trench in the ground and place water using your buckets on both of the outer blocks to create a standard infinite water source in the center. Place the Ad Astra Water Pump directly above the middle water source block. Ensure the bottom face of the Water Pump is touching the water, as this is the specific face that draws liquid in.
Tip: Do not place the pump above flowing water; it must be directly over a stationary source block to work continuously.
2Power the Water Pump and Oxygen Loader
Place your Oxygen Loader nearby where you can easily access it. Run Steel Cables or Desh Cables from your power source (such as a Coal Generator or Solar Panel) to both the Water Pump and the Oxygen Loader. Verify in both machine interfaces that their internal energy bars are completely filled before moving on to the fluid plumbing.
Tip: Machines can accept energy from almost any side, so route your power cables behind or underneath them to keep the top and front clear for fluid pipes.
3Connect the Fluid Pipes
Run a line of Desh or Ostrum Fluid Pipes from the top or side of the Water Pump directly into the side of the Oxygen Loader. When placed, the pipes will automatically form a physical connection to the machines. However, unlike energy cables, Ad Astra Fluid Pipes will not move fluids until you explicitly tell them which direction to flow.
Tip: Ostrum Fluid Pipes have a higher transfer rate than Desh Fluid Pipes, making them ideal if you plan to expand your oxygen network later.
4Configure Pipe Modes with the Wrench
Equip your Ad Astra Wrench and look at the exact connection point where the Fluid Pipe touches the Water Pump. Shift-right-click (or right-click depending on your mod version and keybinds; watch the visual indicator on the pipe collar) until the pipe connection changes to 'Extract' mode. Next, move to the connection point touching the Oxygen Loader and make sure it is set to 'Insert' mode (which is usually the default state).
Tip: You can also cycle a pipe connection to 'None' with the Wrench to disconnect two adjacent pipes without breaking blocks, which is great for keeping water and fuel lines separate.
5Collect Your Automated Oxygen
Open the Oxygen Loader's GUI to confirm that water is steadily flowing into the left input tank and automatically converting into Oxygen in the right output tank. Place an Oxygen Tank, a Netherite Space Suit, or a Standard Space Suit into the top-right slot of the Oxygen Loader. The machine will instantly transfer the generated oxygen into your gear, keeping it topped off whenever you visit.
Tip: You can use this exact same water-pumping setup to feed an Oxygen Distributor, which creates a breathable room instead of filling tanks.
6Automate the Fuel Refinery
To automate rocket fuel, place a Fuel Refinery connected to your power grid and provide it with Oil (either by pumping it from an oil well or piping it out of a fluid storage tank). Run a separate line of Fluid Pipes from the Fuel Refinery to your Launch Pad. Remember to never connect your water pipes and fuel pipes together, as pipes can only handle one fluid type cleanly at a time.
Tip: Look for large black oil spouts erupting in the ocean biomes to gather raw Oil in bulk.
7Auto-Fuel the Rocket on the Launch Pad
Connect your fuel pipe line directly to the center or edge of the 3x3 Launch Pad, or into a Fluid Tank acting as a buffer. Use your Wrench to set the pipe touching the Fuel Refinery to 'Extract' and the connection at the destination to 'Insert'. When a rocket is placed on the Launch Pad, or if you route the fuel through an adjacent loading setup depending on your specific version of Ad Astra, the fuel will transfer automatically without needing manual buckets.
Tip: Check your Astrodux guidebook to verify if your specific version of Ad Astra allows direct Launch Pad piping or requires an intermediary fluid tank, as this behavior changed slightly across major updates.
How it works
Ad Astra's fluid logistics rely on a strict pull-and-push node system rather than passive gravity or automatic machine ejection. While many tech mods allow machines to automatically push fluids into adjacent pipes, Ad Astra's machines generally wait for an external pipe to actively pull the fluid out. This is why simply placing a Fluid Pipe between a Water Pump and an Oxygen Loader does nothing until you use the Wrench.
When you use the Wrench on a pipe's connector collar to set it to 'Extract', that specific node actively polls the attached block's fluid inventory every few ticks, draws fluid into the pipe's internal buffer, and distributes it toward any connected node set to 'Insert'. The Water Pump itself works by consuming Forge Energy (FE) or Tech Reborn Energy (E) to harvest the water block directly beneath it. If it detects an infinite water arrangement (a source block flanked by two other water source blocks), it generates water indefinitely without actually deleting the block in the world, giving you a maintenance-free supply of raw water for oxygen electrolysis.
Common mistakes
- Forgetting to set the pipe to Extract mode: Simply connecting pipes to a Water Pump or Fuel Refinery will result in zero fluid transfer. Always use the Wrench on the starting pipe collar.
- Placing the Water Pump over a single water block: If the water beneath the pump is not part of an infinite source (like a 3x1 or 2x2 pool), the pump will suck up the single block and immediately stop working.
- Cross-contaminating fluid lines: Letting a water pipe accidentally connect to a fuel or oil pipe will jam the network, as a single pipe line cannot sort mixed fluids. Use the Wrench to disconnect touching pipes.
- Using Energy Cables instead of Fluid Pipes: Steel and Desh Cables look slightly similar to Desh and Ostrum Fluid Pipes. Double-check the item tooltip in JEI if your fluids refuse to move.
FAQ
Why isn't my Water Pump pumping any water?
Check three things: ensure the pump has power, verify there is a stationary water source block directly underneath its bottom face, and make sure the attached Fluid Pipe is wrenched into 'Extract' mode.
Does the Water Pump work on the Moon or Mars?
Yes, as long as you can place a liquid water source block beneath it (such as inside a sealed, heated, or oxygenated base where water does not immediately freeze or evaporate), the pump will function normally.
How do I clear a Fluid Pipe if the wrong liquid gets stuck inside?
The fastest and most reliable way to flush an Ad Astra Fluid Pipe is to break the contaminated pipe segments with a pickaxe and place them back down.
Can I use fluid pipes from other mods with Ad Astra machines?
Yes, Ad Astra uses standard Forge and Fabric fluid APIs, so pipes from mods like Mekanism, Pipez, or Modern Industrialization will smoothly interface with the Water Pump, Oxygen Loader, and Fuel Refinery.
By mastering the Wrench's extract and insert modes on Fluid Pipes, you can seamlessly route infinite water into Oxygen Loaders and refined fuel straight to your rockets for a completely automated space program.