GregTech CEu Modern · Power · Beginner

GregTech Electricity Explained: Voltage, Amperage, and Cable Loss

Mastering the electrical system in GregTech CEu Modern is the single most important step to automating your factory without blowing it up. This guide breaks down the logic behind Energy Units (EU), Voltage, Amperage, and Cable Loss so you can design safe, efficient power grids from Low Voltage (LV) all the way to the endgame. By the end, you will know how to match cables to generators, use Battery Buffers, and step power up or down with Transformers without causing machine explosions or cable fires.

What you need

  • A basic power generator (such as a Basic Steam Turbine or Basic Combustion Generator)
  • Insulated cables matching your tier (such as 1x or 4x Tin Cable for LV)
  • Power consumers (such as a Basic Wiremill or Basic Bending Machine)
  • A Battery Buffer and matching tier Batteries (such as a 4x LV Battery Buffer with Small Sodium Batteries)
  • A Transformer (such as an LV Transformer to connect LV and MV networks)
  • GregTech Wire Cutters, Wrench, and a Soft Mallet

Step by step

  1. 1Read Your Generator and Machine Tooltips

    Before placing any blocks, open your inventory or JEI and hover over your Basic Steam Turbine and Basic Wiremill. Note the Voltage tier (LV, which equals 32 EU/t) and the Amperage ratings listed in the tooltip. A standard single-block generator outputs 1 Amp of its tier's voltage, while standard machines request 1 Amp when actively processing a recipe.

    Tip: Hold Shift while hovering over any GregTech machine or cable in JEI to reveal its exact EU/t limits, amperage capacity, and loss per block.

  2. 2Select and Craft the Correct Cable

    Look up Tin Cable in JEI for your LV network. You will see three critical numbers: Max Voltage (32 EU/t), Max Amperage (varies from 1A to 16A depending on thickness), and Loss/Meter/Amp (typically 1 EU per block for insulated Tin). Always craft insulated cables by combining bare wires with rubber in an Assembler or crafting grid, as uninsulated wires damage you on contact and suffer higher energy loss.

    Tip: In each voltage tier, unlocking the superconductor wire of that tier allows you to transport power with zero EU loss per block.

  3. 3Connect Your First 1-Amp Circuit

    Place your Basic Steam Turbine down and notice the distinct output dot on one of its faces. Rotate that dot using a Wrench so it faces where you want your cable to go, then connect a short line of 1x Tin Cable from that output face to your Basic Wiremill. Keep the cable run under 4 blocks long so cable loss does not consume a noticeable fraction of your 32 EU/t packet.

    Tip: Use GregTech Wire Cutters on two adjacent cable blocks if they fail to connect automatically, or to disconnect two parallel power lines that you want to keep separate.

  4. 4Stabilize Multi-Machine Grids with a Battery Buffer

    If you connect four LV machines to a single Basic Steam Turbine, your machines will stutter and lose recipe progress because one turbine only provides 1A while four active machines demand 4A. Place a 4x LV Battery Buffer between your generator and your machines, facing the output dot toward your machine line. Place up to four LV batteries (like Small Lithium or Sodium Batteries) inside the buffer so it can absorb 1A continuously and burst-output up to 4A when multiple machines run at once.

    Tip: If you use a 4x Battery Buffer, you must upgrade the cable connected to its output to at least a 4x Tin Cable, or the cable will catch fire when all four batteries discharge simultaneously.

  5. 5Step Power Down Safely with a Transformer

    When you reach Medium Voltage (MV, 128 EU/t), you can power four LV machines using a single MV generator by placing an LV Transformer between them. By default, a newly placed Transformer steps power down: its single five-dot face accepts 1A of the higher voltage (MV, 128 EU/t), and its other five single-dot faces output up to 4A total of the lower voltage (LV, 32 EU/t). Connect your MV Copper Cable to the single higher-tier input face, and connect a 4x Tin Cable to one of the lower-tier output faces.

  6. 6Step Power Up for Higher-Tier Machines

    If you want to run one MV machine (requiring 128 EU/t) using four LV generators (producing 32 EU/t each), right-click the LV Transformer with a Soft Mallet. A chat message will confirm it has switched to Step-Up mode, reversing the face roles. Now feed 4A of LV power into the lower-voltage faces using 4x Tin Cable, and draw 1A of MV power out of the single higher-voltage face using a 1x Copper Cable.

    Tip: Always double-check which face has the single dot versus the group of dots before connecting live generators.

How it works

GregTech electricity does not flow like a simple pool of energy; instead, it is simulated as discrete packets defined by Voltage (EU/t) and Amperage (the number of packets sent per tick). Voltage tiers scale up by a factor of four each time: LV is 32 EU/t, MV is 128 EU/t, HV is 512 EU/t, EV is 2048 EU/t, continuing all the way to UHV and beyond. A machine of a given tier can only accept packets of its exact tier or lower, while a cable can only survive packets up to its rated Voltage and Amperage.

Power in GregTech is pull-based rather than push-based. Generators and Battery Buffers only send an energy packet down a cable when a connected machine or energy storage block actively requests it. Voltage determines whether the receiving machine survives the packet: if an MV packet (128 EU/t) hits an LV machine (max 32 EU/t), the machine immediately explodes. Amperage determines whether the cable survives: if four LV machines request 1A each through a 1x Tin Cable rated for 2A, the cable receives 4A, overheats, catches fire, and melts.

Cable loss applies a flat EU tax to every individual packet (Amp) for every block it travels. If a 32 EU/t LV packet travels across 5 blocks of cable that has a loss of 2 EU/block, the packet arrives at the machine with only 22 EU. Because the machine still needs its full recipe cost per tick, it may require an extra Amp to make up the deficit, which unexpectedly doubles your cable's amperage load and risks burning your wires.

Common mistakes

  • Connecting a higher-voltage cable directly to a lower-tier machine: Even 1 Amp of MV power (128 EU/t) sent into an LV machine will cause an immediate explosion. Always use the appropriate Transformer to step down voltage first.
  • Ignoring cable loss when sizing amperage: If your cable loses even 1 EU per block, a machine requiring nearly the full tier voltage (like a 30 EU/t recipe in an LV machine) will pull 2 Amps instead of 1 Amp to compensate for the lost EU. Always leave extra amperage headroom on your cables or keep wires as short as possible.
  • Leaving electric machines exposed to the sky: Rain, thunderstorms, or water contact on any active GregTech electric machine or Battery Buffer will cause it to violently explode. Build a roof over your factory before wiring anything up.
  • Using thin cables on a large Battery Buffer output: A 16x Battery Buffer loaded with 16 batteries can output 16 Amps at once if your factory demands it. Connecting a 4x cable to a full 16x buffer will burn the cable as soon as five or more machines turn on simultaneously.

FAQ

Why is my machine constantly pausing and restarting its recipe?

Your machine is starving for EU/t. Either your generator cannot keep up with the total EU/t demand of your active machines, or cable loss has reduced the arriving packet's EU below what the recipe needs per tick. Shorten your cables, add a Battery Buffer, or add another generator.

Can I feed two LV Amps (2x 32 EU/t) into an MV machine to run a 64 EU/t recipe?

Technically an MV machine will accept LV packets without exploding, and two Amps of 32 EU/t equal 64 EU/t before cable loss. However, even 1 EU of cable loss will drop two LV packets below 64 EU/t, causing the recipe to fail. It is much safer to step the 4A of LV power up to 1A of MV (128 EU/t) using an LV Transformer.

Why did my cable burn when my generator only outputs 1 Amp?

You likely have a Battery Buffer or multiple generators on that line. Because electricity is pull-based, if four machines on the far end request power simultaneously, a Battery Buffer or bank of four generators will send 4 Amps down the line at once, burning any 1x or 2x cable in between.

How do I minimize cable loss over long distances?

Step your power up to a higher voltage tier using Transformers, transmit it over a high-voltage cable, and step it back down near the machines. Because each higher tier carries four times the EU per Amp, losing 1 or 2 EU per block on an HV or EV packet wastes a tiny fraction of energy compared to losing 1 or 2 EU on an LV packet.

Keep your GregTech CEu Modern factory safe and efficient by matching machine voltage tiers to prevent explosions, sizing cable thickness to total requested amperage to prevent fires, and keeping wire runs short to avoid cable loss.

More GregTech CEu Modern guides

GregTech CEu Modern · Getting startedGregTech CEu Modern Getting Started: Conquering the Bronze and Steam AgeEmbarking on a GregTech CEu Modern playthrough requires unlearning standard Minecraft habits and mastering complex industrial mechanics from day one. This guide will walk you through locating massive ore veins, assembling your first manual tools, harnessing steam power, and constructing the Primitive Blast Furnace. Mastering this initial Bronze and Steam Age is essential, as it lays the infrastructure required to produce Steel and unlock the first tier of electricity.Beginner8 steps
GregTech CEu Modern · ExplainedGregTech CEu Modern Ore Generation & Prospecting ExplainedMining in GregTech CEu Modern requires a complete shift away from vanilla strip-mining because ores generate in massive, scattered veins rather than small clusters. This guide teaches you how to locate these colossal ore deposits using recipe viewer data, surface indicator rocks, and electronic Prospector's Scanners. Mastering this system early will save you hours of blind digging and secure thousands of raw resources for your industrial revolution.Beginner6 steps
GregTech CEu Modern · ProgressionLV to HV Progression Guide: Circuit Tiers, EBF, and CleanroomsTransitioning from the Steam Age through Low Voltage (LV) and Medium Voltage (MV) into High Voltage (HV) is the first major hurdle in GregTech CEu Modern. This guide covers the essential steps to automate circuit production, master the Electric Blast Furnace (EBF), set up Petrochemistry for Polyethylene, and construct your first sterile Cleanroom. Mastering these foundational systems will unlock advanced automation and prepare your base for late-game manufacturing.Intermediate7 steps
GregTech CEu Modern · Setup guideHow to Build an Automated GregTech Ore Processing LineSetting up an automated ore processing line in GregTech CEu Modern is essential for transitioning from manual resource gathering to scalable industrial production. While simple smelting turns raw ores into ingots, a full processing array uses Macerators, Ore Washers, Thermal Centrifuges, and Sifters to multiply your output and extract rare byproducts that cannot be obtained any other way. By the end of this guide, you will have a self-routing, filter-controlled pipeline that automatically sorts and processes every raw ore into pure dust and gems.Intermediate7 steps
GregTech CEu Modern · AutomationGregTech Covers & Logistics Explained: Pumps, Conveyors, and Robot ArmsMastering logistics in GregTech CEu Modern requires moving beyond simple pipe networks and utilizing machine covers for precise resource control. This guide explains the underlying mechanics of native machine auto-output, how to attach and configure Conveyor Modules, Electric Pumps, and Robot Arms, and how to control flow direction using Shutter Modules. By learning these systems, you will eliminate processing bottlenecks and prevent jammed multi-input machines.Intermediate6 steps
GregTech CEu Modern · PowerGregTech Power Generation Guide: Benzene, Diesel, and Large TurbinesIn GregTech CEu Modern, transitioning from early-game Steam to mid- and late-game voltages requires massive, automated power production. This guide covers the blueprints and underlying logic for the two main chemical fuel paths—renewable Benzene and high-density Cetane-Boosted Diesel—and explains how to scale them into the endgame using Large Turbines.Intermediate6 steps