Ad Astra · Mid game
Ad Astra Sealed Lunar Life Support & Oxygen Habitat
This Ad Astra mid-game setup establishes a fully pressurized, breathable lunar habitat with Earth-normal gravity. By combining automated water electrolysis with an Oxygen Distributor and Gravity Normalizer, you can safely remove your space suit while operating inside your off-world base. It relies on renewable solar power and an infinite water source to keep life support running indefinitely without player intervention.
- Footprint
- 9x9x5 blocks (interior sealing volume varies)
- Power
- Moderate continuous FE/t (check JEI for exact distributor load)
- Throughput
- Continuous oxygen & 1.0G gravity coverage for up to ~3,000 blocks
- Difficulty
- intermediate
Flow diagram
How items, fluids and energy move through the setup, left to right.
Swipe sideways to see the whole diagram
Materials
| Item | Count |
|---|---|
| Oxygen Distributor | 1 |
| Gravity Normalizer | 1 |
| Oxygen Loader | 1 |
| Water Pump | 1 |
| Solar Panel | 6 |
| Etrionic Capacitor | 2 |
| Steel Cable | 16 |
| Desh Fluid Pipe | 12 |
| Wrench | 1 |
| Steel Sliding Door | 2 |
| Stone Button | 4 |
| Iron Plating | 256 |
| Water Bucket | 2 |
Build it step by step
1Construct the Sealed Hull
Build an enclosed room up to 9x9x5 using solid, airtight blocks such as Iron Plating or Reinforced Glass. Ensure every corner and edge is completely sealed off from the lunar vacuum, as any missing block or non-full block (like stairs or slabs) will cause an oxygen leak.
2Install the Airlock
Create a small 3x3 vestibule attached to the main room and install two Steel Sliding Doors in series. Place buttons on both sides of each door so you can cycle through the airlock one door at a time, preventing the room from depressurizing when you enter or exit.
3Set Up the Infinite Water Well
Inside the utility corner of your base, dig a 1x3 trench and use your two Water Buckets to create a vanilla infinite water source. Place the Ad Astra Water Pump directly above the center source block so it can continuously extract water without draining the pool.
4Place Life Support Machines
Place the Oxygen Loader adjacent to or near the Water Pump. In the center of your habitat floor or ceiling, place both the Oxygen Distributor and the Gravity Normalizer so their effective voxel reach easily covers the entire room.
5Plumb the Water and Oxygen Pipes
Connect the Water Pump to the Oxygen Loader using Desh Fluid Pipes, then run another separate line of Desh Fluid Pipes from the Oxygen Loader to the Oxygen Distributor. Use the Ad Astra Wrench to configure the pipe ends: set the Pump side to extract water, and the Oxygen Loader output side to extract produced oxygen into the Distributor.
6Deploy the Roof Solar Grid
Mount your Solar Panels on top of the habitat roof where they have unobstructed sky access. Run a line of Steel Cables down through a solid block into your utility corner—do not leave an open hole for cables, or the room will fail to seal.
7Wire the Capacitor and Machines
Connect the roof cable line into the two Etrionic Capacitors to buffer energy for the lunar night cycle. From the capacitors, run Steel Cables to the Water Pump, Oxygen Loader, Oxygen Distributor, and Gravity Normalizer.
8Verify Seal and Activate
Open the GUI of the Oxygen Distributor and toggle the visibility overlay to verify that the oxygen volume turns green and fills the chamber without leaking. Similarly, open the Gravity Normalizer GUI, set the target gravity to 1.0G, and confirm its field covers the floor space.
How it works
The core of this life support loop relies on continuous in-situ water electrolysis. The Water Pump draws water from a self-replenishing vanilla infinite water source and pushes it via Desh Fluid Pipes into the Oxygen Loader. Once powered, the Oxygen Loader converts liquid water directly into breathable Oxygen gas. That Oxygen is then piped directly into the Oxygen Distributor, which floods the enclosed interior volume with a breathable atmosphere.
Simultaneously, the roof-mounted Solar Panels harvest augmented solar energy—which is more efficient on the airless Moon than on Earth—and store surplus power inside the Etrionic Capacitors. These capacitors act as an uninterruptible power supply during the lunar night, feeding continuous Forge Energy via Steel Cables to the Oxygen Distributor and Gravity Normalizer. Because the airlock prevents atmosphere escapes during player transit, the Distributor only consumes minimal upkeep oxygen to maintain pressure.
Upgrades and scaling
- Replace the Oxygen Loader and Distributor fluid piping with Ostrum Fluid Pipes and Ostrum Cables for much higher transfer rates when expanding to multi-room habitats.
- Add an Energizer and a Cryo Freezer module inside the habitat to recharge high-tier Jet Suits and produce Cryo Fuel from extra ice mined on the Moon.
- Link an Oxygen Sensor block to your airlock doors and an alarm lamp using redstone so the outer door automatically locks if indoor oxygen drops unexpectedly.
- Scale up the Etrionic Capacitor bank or supplement power with a Coal Generator or fusion setup from companion tech mods if you expand the base past several thousand blocks.
Common mistakes
- Leaving both airlock doors open at the same time, which vents the entire room's oxygen into space and drains your capacitor and oxygen buffers.
- Using slabs, stairs, or vanilla glass panes in the outer wall structure; Ad Astra's seal check requires full, solid bounding boxes to hold pressure.
- Cross-connecting the Water pipe line and the Oxygen pipe line into a single shared Desh Fluid Pipe, which clogs the system with mixed fluids.
- Forgetting to use the Wrench to set the Desh Fluid Pipe connections to 'Extract' mode on both the Water Pump and the Oxygen Loader output.
- Relying solely on Solar Panels without Etrionic Capacitors, causing the oxygen field to collapse and suffocate the player as soon as the lunar night begins.
FAQ
Why won't my water source stay liquid when I place it on the Moon?
Water immediately freezes or vaporizes in an unpressurized vacuum depending on the planetary temperature, or if placed before the room is sealed. If needed, pressurize the room temporarily using a pre-filled Oxygen Tank inside the Oxygen Distributor first, then place your water source blocks.
How many blocks can a single Oxygen Distributor support?
A single Oxygen Distributor can fill a few thousand blocks of interior volume (check JEI or the machine GUI in your specific mod version for the exact maximum block count). If your base is larger, partition it with internal sliding doors and use one Distributor per zone.
Can I fill my Space Suit directly from this setup?
Yes. Because the Oxygen Loader is constantly producing oxygen, you can place an empty Oxygen Tank or your Space Suit Chestplate straight into the Oxygen Loader's internal inventory slot to top it off before going on lunar excursions.