Modular Machinery Reborn · End game

Parallel Endgame Assembly Line

The Parallel Endgame Assembly Line is a pinnacle factory setup using Modular Machinery Reborn to mass-produce complex late-game components. By integrating maximum-tier Parallel Controllers with Ludicrous Energy Input Hatches, this single structure executes dozens of crafting operations simultaneously. It eliminates the lag and sprawling footprint of traditional machine arrays while satisfying the immense crafting demands of endgame modpacks.

Footprint
11x11x7 blocks
Power
Massive FE/t at full load (check JEI for pack-specific recipe costs)
Throughput
Up to 64x or 256x operations per cycle depending on controller tier
Difficulty
advanced

Flow diagram

How items, fluids and energy move through the setup, left to right.

Swipe sideways to see the whole diagram

Forge Energy (FE)Crafting IngredientsLubricant & CoolantsInternal Structure PowBatch ItemsBatch FluidsParallel Processing MoAssembled Endgame CompFinished ProductsEndgame Power BufferPOWERLudicrous Energy InputHatchINPUTRaw Material StorageSTORAGEHuge Item Input BusINPUTFluid ReservoirSTORAGEHuge Fluid Input HatchINPUTParallel Controller(Ultimate)CONTROLModular MachineControllerMACHINEHuge Item Output BusOUTPUTFinished ComponentStorageSTORAGE
InputMachinePowerStorageOutputControlItemFluidEnergySignal

Materials

ItemCount
Modular Machine Controller1
Machine Casing140
Reinforced Machine Casing64
Machine Vent24
Machine Circuitry16
Machine Gearbox12
Parallel Controller (Ultimate)2
Ludicrous Energy Input Hatch2
Huge Item Input Bus4
Huge Fluid Input Hatch2
Huge Item Output Bus2
Machine Blueprint1

Build it step by step

  1. 1Verify the Blueprint in JEI

    Before placing blocks, craft the Machine Blueprint for your pack's endgame assembler and inspect the exact structure in JEI. Hold the blueprint in your off-hand to project a 3D holographic guide in the world. Ensure you have cleared an 11x11x7 area and that the entire structure fits comfortably within a single chunk to prevent multiblock corruption.

  2. 2Lay the Foundation and Input Buses

    Build the base layer using Machine Casings and Reinforced Machine Casings according to the hologram preview. Embed the four Huge Item Input Buses and two Huge Fluid Input Hatches into the bottom or lower-side edges so logistics pipes can easily access them from below the floor. Leave the front-center block on the second layer open for the Modular Machine Controller.

  3. 3Install the Internal Functional Blocks

    Construct the inner core of the assembly line using Machine Gearboxes and Machine Circuitry blocks. These high-tier internal components are strictly required by endgame recipes to validate the structure. Take care not to substitute these with standard casings, as only specific outer frame blocks allow hatch replacements.

  4. 4Mount the Parallel and Energy Hatches

    Place the two Ultimate Parallel Controllers and the two Ludicrous Energy Input Hatches into the designated casing slots along the rear wall. Combining multiple energy hatches ensures the internal buffer can handle the massive per-tick energy draw multiplied by the parallel processing factor. Connect your highest-tier power cables directly to the energy hatches.

  5. 5Complete the Frame and Vents

    Finish building the upper walls and roof using the remaining Reinforced Machine Casings and Machine Vents. Place the Modular Machine Controller into the front slot and insert the Machine Blueprint inside its GUI if required by your modpack configuration. The controller interface should now display a 'Structure Formed' confirmation message.

  6. 6Configure Logistics and Buffers

    Hook up your storage network interfaces to the Huge Item Input Buses and Huge Fluid Input Hatches. Ensure your item supply system is configured to push full stacks rapidly, as parallel processing will consume hundreds of items in a single tick. Route the Huge Item Output Buses directly back into your primary storage system.

How it works

At the heart of Modular Machinery Reborn is the dynamic multiblock evaluation system. The Modular Machine Controller constantly scans its connected buses and hatches at the start of a crafting cycle. When the Ultimate Parallel Controllers are installed in the structure frame, they multiply the base recipe capabilities. If a standard recipe crafts one endgame circuit using 10,000 FE/t, a 64x parallel setup allows the controller to instantly pull 64 sets of ingredients from the Huge Item Input Buses and process them all within the exact same duration as a single item.

To sustain this massive multiplier, standard hatches would bottleneck immediately. The design utilizes multiple Huge Item Input Buses and Huge Fluid Input Hatches so that dozens of distinct ingredient stacks can sit buffered inside the machine simultaneously. Similarly, parallel processing multiplies the energy cost per tick linearly. Using dual Ludicrous Energy Input Hatches guarantees that the internal energy buffer remains saturated, preventing the machine from stalling or resetting progress mid-cycle due to power starvation.

If your modpack integrates Modular Diversity or specific environmental constraints, the controller also validates conditions like structural tiering or fluid coolant presence every tick. By separating raw item inputs at the front, fluid coolants on the sides, and heavy power cabling at the rear, this layout prevents cable spaghetti and gives players clear access to upgrade individual hatches without tearing down the core Machine Circuitry.

Upgrades and scaling

  • Add additional Parallel Controllers up to the structural casing replacement limit to further multiply batch output per cycle.
  • Upgrade Huge Item Input Buses to Ludicrous or Ultimate tiers if recipes require more inventory slots per bus.
  • Install Smart Interface or Redstone Relay ports to automatically toggle the controller off when your storage system reaches a desired stock threshold.
  • Add Secondary Fluid Output Hatches if your specific modpack recipes generate superheated steam or waste fluids during assembly.

Common mistakes

  • Building the multiblock across chunk boundaries, which causes the Modular Machine Controller to lose track of outer hatches when chunks unload.
  • Underestimating the multiplied FE/t cost; if your energy hatches cannot hold enough total power for the parallel batch, the recipe will pause or fail to start.
  • Replacing mandatory structural blocks (like Machine Vents or Machine Gearboxes) with hatches; hatches can only replace designated standard Machine Casings.
  • Using small Output Buses that fill up in a single cycle; if the output inventory cannot fit the entire multiplied batch, the machine will halt operation.

FAQ

Why does my controller say the structure is formed, but the recipe won't start?

Check your Output Bus capacity and Energy Input Hatch tier. In parallel mode, the machine requires enough free output slots and energy buffer to cover the active batch size before it begins.

Can I share hatches between two adjacent Modular Machines?

While some versions allow hatch sharing on overlapping walls, it is heavily discouraged for parallel setups because two controllers fighting over the same Energy or Item Input Hatch will cause severe throughput stuttering.

How do I know which blocks can be replaced by hatches?

Check the structure preview in JEI; blocks that cycle through different hatch types in the preview animation are valid replacement spots, which are almost always standard Machine Casings.

More Modular Machinery Reborn designs