Industrial Reborn · Mid game
Industrial Reborn Geothermal Lava Power Plant
This Industrial Reborn Geothermal Lava Power Plant provides a reliable, mid-game energy backbone by harvesting deep lava lakes to fuel an array of Geothermal Generators. Unlike solid-fuel setups that require constant tree farming or coal mining, this system operates semi-autonomously once positioned over a large lava source. It routes all generated energy into a central MFE and steps it down safely for your base's standard machinery.
- Footprint
- 9x7x5 blocks
- Power
- Steady mid-tier EU output (check JEI for exact Geothermal Generator EU/t values)
- Throughput
- Continuous lava consumption scaled to active base load
- Difficulty
- intermediate
Flow diagram
How items, fluids and energy move through the setup, left to right.
Swipe sideways to see the whole diagram
Materials
| Item | Count |
|---|---|
| Geothermal Generator | 4 |
| Pump | 1 |
| MFE | 1 |
| LV Transformer | 1 |
| Insulated Gold Cable | 16 |
| Insulated Copper Cable | 12 |
| Empty Cell | 64 |
| Hopper | 6 |
| Chest | 4 |
| Lever | 1 |
| Wrench | 1 |
Build it step by step
1Position the Pump
Locate a large underground lava lake or a Nether lava ocean. Place the Industrial Reborn Pump directly above the deepest accessible lava source block so its intake tube can reach the fluid.
2Set Up Cell Logistics
Place a Hopper pointing into the top or side of the Pump, topped with a Chest filled with stacks of Empty Cells. Placeanother Hopper directly beneath or adjacent to the Pump's output slot leading into a buffer Chest to collect filled Lava Cells.
3Construct the Geothermal Array
Build a platform nearby and place four Geothermal Generators in a neat row. Leave one block of space above and behind them for item distribution and cable routing.
4Connect Fuel Distribution
Place Hoppers above each Geothermal Generator connected to your Lava Cell transport chest, or manually distribute stacks of Lava Cells from the buffer chest into the generators to prime the system.
5Wire the Generator Grid
Run Insulated Gold Cables along the back of all four Geothermal Generators. Route one branch of this cable back to the Pump to keep it self-powered, and route the main trunk line toward your energy storage area.
6Install the MFE Storage
Place the MFE at the end of the Insulated Gold Cable trunk line. Make sure the single output dot on the MFE faces away from the incoming generator cables, using your Wrench to rotate it if needed.
7Step Down the Voltage
Place an LV Transformer directly against the output face of the MFE, making sure the high-voltage face (three dots) connects to the MFE output dot. Run Insulated Copper Cables from the single-dot faces of the LV Transformer out to your basic machines.
How it works
The core advantage of the Geothermal Generator in Industrial Reborn is its load-balancing behavior. Unlike standard solid-fuel Generators that burn through coal continuously even when internal buffers are full, Geothermal Generators halt lava consumption the exact moment their internal energy buffer and connected storage reach maximum capacity. This guarantees zero wasted fuel during idle periods.
The Pump draws raw lava from the world and packages it into Empty Cells, creating stackable Lava Cells. A small fraction of the EU produced by the Geothermal Generators is looped back to the Pump, creating a closed, self-sustaining cycle that runs until the lava lake is completely drained or the Empty Cells run out.
Because four Geothermal Generators combined with an MFE operate at Medium Voltage tiers, connecting the MFE directly to basic Tier 1 machines (like an Electric Furnace or Macerator) will cause them to overload or fail. The LV Transformer safely steps the MFE's Medium Voltage output packets down into Low Voltage packets suitable for standard Insulated Copper Cables and starter machines.
Upgrades and scaling
- Expand the array to 8 or 12 Geothermal Generators to saturate the MFE charging rate during heavy ore-processing sessions.
- Upgrade the MFE to an MFSU and add an MV Transformer once you craft Glass Fibre Cables and transition into high-voltage machinery.
- Add Overclocker Upgrades to the Pump if lava extraction lags behind your generators' consumption rate during peak factory demand.
Common mistakes
- Using uninsulated cables, which shocks players walking nearby and wastes energy.
- Connecting the MFE output directly to basic Tier 1 machines without an LV Transformer in between.
- Orienting the MFE or LV Transformer backward—always remember that the multi-dot face accepts higher voltage and the single-dot face outputs power (check your Wrench orientation).
- Breaking machines with a pickaxe instead of an Industrial Reborn Wrench, which can destroy the machine block or drop a basic Machine Casing instead of the unit.
FAQ
Why did my Pump stop extracting lava even though it has power?
Check if the lava directly beneath the Pump has turned into obsidian or drained out of reach, or ensure the Empty Cell input chest hasn't run dry.
Do I lose the Tin Cells when the Geothermal Generator burns Lava Cells?
In standard Industrial Reborn mechanics, Lava Cells are consumed entirely as fuel inside the Geothermal Generator; check JEI in your specific modpack version to see if empty cells are returned.
Can I pipe fluid lava directly into the Geothermal Generators?
If you are playing solely with Industrial Reborn, using Cells with Hoppers is the standard method. If your modpack includes a compatible fluid-pipe mod, you can pump liquid lava directly from the Pump into the generators without using cells.