Flux Networks · Late game
CC: Tweaked Smart Power Grid Control Room
This late-game control room integrates Flux Networks with CC: Tweaked to provide a centralized dashboard for your entire base's power grid. By reading network telemetry through a Flux Controller, the system renders real-time energy input/output graphs on a giant wall monitor and automatically triggers backup generators when your Gargantuan Flux Storage drops below a critical threshold.
- Footprint
- 7x5x4 blocks
- Power
- Minimal (~50 FE/t for CC: Tweaked peripherals, check JEI)
- Throughput
- Unlimited FE/t (Bypass Limit enabled)
- Difficulty
- advanced
Flow diagram
How items, fluids and energy move through the setup, left to right.
Swipe sideways to see the whole diagram
Materials
| Item | Count |
|---|---|
| Flux Controller | 1 |
| Gargantuan Flux Storage | 4 |
| Flux Plug | 2 |
| Flux Point | 1 |
| Flux Configurator | 1 |
| Advanced Computer | 1 |
| Advanced Monitor | 15 |
| Wired Modem | 4 |
| Networking Cable | 16 |
| Redstone Dust | 8 |
Build it step by step
1Establish the Flux Network Core
Place your Flux Controller and four Gargantuan Flux Storage blocks in the center of your control room. Right-click the Flux Controller, go to the Network Creation tab, and create a new encrypted network with a custom color. Bind all four Gargantuan Flux Storage blocks to this network so they act as a massive central energy buffer.
2Connect Main and Backup Power Grids
Attach a Flux Plug to your primary base power generation source and a Flux Point to your main machine line, linking both to your new network. Set up a separate array of fuel-based backup generators, attach a second Flux Plug to them, and set that Plug's priority lower than your main power so it only injects energy when running.
3Assemble the Giant Monitor Wall
Construct a 5x3 wall using 15 Advanced Monitors on the front wall of your control room. Make sure they merge into a single seamless display screen. Place an Advanced Computer on a desk facing the screen so you can watch the display while writing your control script.
4Wire the Peripheral Network
Attach a Wired Modem to the Flux Controller, the back of the Advanced Monitor array, and the Advanced Computer. Connect all three modems using Networking Cables. Right-click the Wired Modems on the Flux Controller and the Monitor Array until their borders turn red, registering them on the CC: Tweaked local network.
5Route the Backup Redstone Trigger
Run a line of Redstone Dust (or a fourth Wired Modem connected to a redstone relay peripheral if available in your modpack) from the back of the Advanced Computer to the activation port of your Backup Generators. Ensure the generators are configured to 'Redstone High' activation mode.
6Program the Telemetry and Automation Script
Open the Advanced Computer and create a `startup.lua` script that wraps the Flux Controller peripheral using `peripheral.find()`. Query the network stats every second to fetch current energy input, energy output, and total buffer percentage. Draw these values as scrolling bar graphs on the Advanced Monitor, and add an `if` statement that outputs a high redstone signal to the backup generators whenever stored energy drops below 20%, shutting it off once storage recovers to 80%.
How it works
Flux Networks natively tracks global energy statistics—including tick-by-tick FE/t input, FE/t output, and total storage capacity—inside the Flux Controller. When paired with CC: Tweaked and its compatibility bridge, the Flux Controller acts as a standard peripheral. By wrapping it in Lua, the Advanced Computer can poll these metrics in real time without needing individual energy meters attached to every cable in your base.
The automation logic uses a hysteresis loop (activating at 20% storage and deactivating at 80% storage) to prevent rapid flickering of your backup generators. While your main power generators handle normal daytime or steady-state loads, sudden power spikes from late-game machinery will drain the Gargantuan Flux Storage blocks. Once the 20% threshold is breached, the computer pulls the redstone line high, firing up the backup generators and injecting emergency FE through the backup Flux Plug until the buffer is safely replenished.
Upgrades and scaling
- Enable Chunk Loading directly inside the Flux Controller GUI for all your Flux Plugs and Gargantuan Flux Storage blocks so the grid never goes offline when you travel to other dimensions.
- Add a CC: Tweaked Speaker peripheral to the Networking Cable line and program an audible alarm chime whenever the energy buffer drops below 10% or experiences a massive negative net flow.
- Install an Ender Modem on the Advanced Computer to broadcast power grid metrics to a Pocket Computer, allowing you to monitor FE/t stats and manually toggle backup power from anywhere in the world.
- Use the Flux Configurator to copy and paste Surge Mode or Bypass Limit settings across all Flux Points critical to life-support or containment systems, ensuring they receive priority energy during a brownout.
Common mistakes
- Forgetting to right-click the Wired Modems attached to the Flux Controller and Monitor array; if the modem ring is not glowing red, the computer cannot detect the peripheral.
- Using a single threshold (e.g., turn on below 20%, turn off above 20%) in the Lua script, which causes the backup generators to rapidly stutter on and off every tick at the 20% mark.
- Leaving the Flux Plugs and Points on their default 800,000 FE/t transfer limit when running late-game generators; always toggle 'Bypass Limit' in the GUI for main trunk connections.
- Placing multiple Flux Controllers on the same network; a Flux Network only allows one active Flux Controller at a time, and adding a second one will cause connection conflicts.
FAQ
Why isn't my Advanced Computer recognizing the Flux Controller as a peripheral?
In newer Minecraft versions, native CC: Tweaked integration requires either a compatibility addon mod (such as a dedicated Flux-CC bridge or Plethora/Advanced Peripherals depending on your modpack version). Check JEI and your mod list to confirm the bridge addon is installed, and verify the Wired Modem is activated (glowing red).
Can the computer directly toggle a Flux Plug on and off instead of using Redstone?
Most versions of the peripheral API are read-only for network statistics to prevent server lag and abuse. Controlling your backup generators directly via a redstone signal from the computer is much more reliable and stops the generators from wasting fuel while idle.
How much energy can the Gargantuan Flux Storage actually hold?
A single Gargantuan Flux Storage holds a massive amount of energy (typically 128,000,000 FE by default, though modpacks frequently alter this—check JEI or the block tooltip). You can add dozens of them to the same network, and the Flux Controller will automatically sum their total capacity for your computer script.